Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/29 ▾
  1. 1.Structure & Foundation0/5
    1. Footings, soil movement and foundation crack patterns
    2. Water below grade and in crawl spaces
    3. Load path, columns and floor framing
    4. Roof framing: rafters, ridges and trusses
    5. Decay and wood-destroying organisms
  2. 2.Roofing, Exterior & Site0/5
    1. Roof coverings: how they keep water out and how they fail
    2. Flashings and roof penetrations
    3. Roof drainage, ice dams and chimney tops
    4. Walls, cladding and windows as drained assemblies
    5. Decks, grading and retaining walls
  3. 3.Electrical Systems0/5
    1. Service entrance and capacity
    2. Grounding, bonding and the neutral
    3. Inside the panel: overcurrent protection and terminations
    4. Ground-fault, arc-fault and receptacle testing
    5. Older wiring, workmanship defects and generators
  4. 4.Plumbing Systems0/4
    1. Water supply and piping materials
    2. Traps, vents and drain defects
    3. Water heaters, relief valves and gas connections
    4. Cross-connections, backflow and fixture leaks
  5. 5.HVAC, Insulation & Ventilation0/5
    1. Furnace combustion safety
    2. Venting, draft and house depressurization
    3. Boilers, heat pumps and air conditioning
    4. Insulation, air barriers and vapor retarders
    5. Attic ventilation, crawl spaces and exhaust ducts
  6. 6.Standards, Ethics & Reporting0/5
    1. What a home inspection is and is not
    2. Material defects and how to classify findings
    3. Writing the report: methods, limits and wording
    4. Exclusions, environmental hazards and immediate dangers
    5. Agreements, confidentiality and conflicts of interest
Saved in this browser. Move it to another device →
← Roofing, Exterior & Site

Chapter 2 · Lesson 2 of 5

Flashings and roof penetrations

1 min read

Every flashing question reduces to one rule: upper pieces lap over lower pieces so water is handed down and out.

Where a roof meets a sidewall, individual step flashings are woven in, one per shingle course, with the wall's water-resistive barrier and siding lapped over them. One continuous L-shaped strip caulked to the siding has no drainage path and depends entirely on sealant.

  • Kickout flashing: the angled piece at the bottom of a roof-to-wall intersection that throws concentrated runoff into the gutter. Without it, water runs behind the cladding and rots sheathing and framing out of sight.
  • Chimney counterflashing: let into a mortar joint or reglet and lapped down over the base flashing. A bead of sealant against the brick face is not a substitute.
  • Pipe boots: rubber collars harden and split in sunlight long before the shingles wear out, and roofing cement troweled over them is evidence of a past patch, not a repair.

Check yourself

1. A sloped roof intersects a two-story wall and terminates just above a gutter. There is no diverter at the lower end of the roof-to-wall flashing. Inside, the ceiling and wall below show staining, and the siding at that corner is soft. What is the most likely explanation?

2. Where a sloped roof meets a vertical sidewall, the inspector finds one continuous L-shaped metal strip running the full length of the intersection, with its vertical leg caulked to the siding. Why is this a defect?

Facts checked 2026-11-15 · Sources: National Home Inspector Examination (EBPHI), InterNACHI Home Inspection Standards of Practice

Home Inspector Practice Test (NHIE) cheat sheet: every key fact on one page →