FAA A&P Mechanic (General) Cheat Sheet: Key Facts
Every key takeaway and common trap from the FAA A&P Mechanic (General) study guide on one page, grouped by chapter. Tap a lesson link to read the full explanation.
37 facts · 5 chaptersFacts checked 2026-11-15
Chapter 1
Regulations, Records & Publications
Key takeaways
- A mechanic may approve return to service only for work that is not a major repair or major alteration; after major work the approval comes from an IA holder, a repair station, or the manufacturer. → What an A&P mechanic may do and approve
- An A&P may perform and approve a 100-hour inspection, but an annual inspection requires an Inspection Authorization. → What an A&P mechanic may do and approve
- A 43.9 maintenance entry needs a description of the work, the completion date, and the approver's signature, certificate number and kind of certificate. → Writing maintenance and inspection record entries
- Form 337 for a major repair or alteration is made at least in duplicate, and the FAA copy is sent within 48 hours of approval for return to service. → Major or minor work, approved data and FAA Form 337
- Up to 10 hours past a 100-hour inspection is allowed only en route to the inspection, and that time is charged to the next interval. → Keeping records, AD status and inspection timing
Common trap
- Answers that say "since it was done with approved data" or "any mechanic with both ratings" may sign off a major alteration are wrong. Approved data lets you do the work; it does not give you the authority to approve it. → What an A&P mechanic may do and approve
- Distractors move the Form 337 clock to the start of the job or stretch it to 10 days. The 48 hours start when the work is approved for return to service. → Major or minor work, approved data and FAA Form 337
- "Approved for return to service with respect to the work performed" is maintenance wording under 43.9. It does not certify an inspection, so it is the wrong pick when the question asks for the 43.11 inspection statement. → Writing maintenance and inspection record entries
Quick reference
| Data type | Examples | Enough for |
|---|---|---|
| Acceptable data | Maintenance manual, instructions for continued airworthiness | Minor repairs and alterations |
| Approved data | TCDS, STC, AD, field approval on Form 337 | Major repairs and alterations |
| Rule | Requirement |
|---|---|
| 65.83 recent experience | Within the preceding 24 months, at least 6 months of mechanic work or supervision, or a finding by the Administrator that you can do the work |
| 65.21 change of address | Written notice to the FAA Airman Certification Branch within 30 days, or you may not use the certificate after that |
| 65.89 display | Kept in the immediate area where you work; shown on request to the Administrator, the NTSB, or law enforcement |
Chapter 2
Basic Electricity
Key takeaways
- Ohm's law is E = I × R, and power is P = E × I = I² × R = E² / R. → Ohm's law, power and what sets a wire's resistance
- In series the current is the same everywhere and the drops add up to the source; in parallel every branch has the full source voltage and the currents add. → Series, parallel and series-parallel circuits
- A fuse or circuit breaker is sized to protect the wire, and a tripped breaker is reset by hand only once. → Wire ratings, circuit protection and test meters
- Lead-acid specific gravity falls as the battery discharges, while nickel-cadmium specific gravity stays nearly constant and water is added only at full charge. → Aircraft batteries and DC motors
- Peak AC voltage is 1.414 times the effective value, and a transformer's voltage ratio equals its turns ratio while current changes the opposite way. → Alternating current, transformers and diodes
Common trap
- When a question gives watts and volts and asks for ohms, dividing one by the other gives a current-type number, not resistance. Use R = E² / P. → Ohm's law, power and what sets a wire's resistance
- Shunt and multiplier get swapped in the distractors. Think of where each meter sits: the ammeter is in series, so its helper is a shunt in parallel; the voltmeter is in parallel, so its helper is a multiplier in series. → Wire ratings, circuit protection and test meters
Quick reference
| Quantity | Series | Parallel |
|---|---|---|
| Current | Same through every part | Branch currents add |
| Voltage | Drops add up to the source | Full source voltage on each branch |
| Total resistance | Sum of the resistors | Less than the smallest branch |
Chapter 3
Weight & Balance, Math & Physics
Key takeaways
- The datum location comes from the Type Certificate Data Sheet or Aircraft Specifications, and CG = total moment / total weight. → Weight and balance terms: datum, empty weight, useful load and MAC
- Subtract tare from each scale reading before computing any moment. → Finding and correcting the center of gravity
- To move cargo, weight to shift = total weight × CG change / distance moved, using the distance between stations, not a station number. → Finding and correcting the center of gravity
- Gas-law problems must be worked in absolute pressure and absolute temperature, then converted back. → Physics for aviation: power, levers, fluids, gases and stress
- One horsepower is 550 foot-pounds per second, or 33,000 foot-pounds per minute. → Finding and correcting the center of gravity
Common trap
- In shift and ballast problems, the denominator is a distance between two points, never a raw station number. For ballast, measure from the ballast arm to the limit you are trying to reach, not to the current CG. → Finding and correcting the center of gravity
- Using the bore as a radius quadruples the displacement, and subtracting the TDC volume before dividing gives a compression ratio one too low. Both wrong numbers often appear among the choices. → Shop mathematics: order of operations, areas, volumes and ratios
- Working a gas-law problem in gauge pressure or in degrees F gives a wrong answer that looks reasonable. Convert to psia and degrees Rankine first, solve, then subtract 14.7 to report gauge pressure. → Physics for aviation: power, levers, fluids, gases and stress
Quick reference
| Formula | Original example |
|---|---|
| Trapezoid area = ½ × (side a + side b) × height | Parallel sides 8 and 12 in, height 5 in: 50 sq in |
| Piston displacement = 0.7854 × bore² × stroke × cylinders | 4 in bore, 3.5 in stroke, 4 cylinders: about 175.9 cu in |
| Compression ratio = volume at BDC / volume at TDC | 63 cu in and 9 cu in: 7 to 1 |
| Driven gear rpm = drive rpm × drive teeth / driven teeth | 24-tooth gear at 1,500 rpm driving a 40-tooth gear: 900 rpm |
Chapter 4
Materials, Hardware & Drawings
Key takeaways
- Tolerance is the total of the plus and minus allowances, and a dimension's own limits override the general note in the title block. → Reading aircraft drawings: lines, sections, tolerances and diagrams
- A flexible hose shortens under pressure, so it is installed with 5 to 8 percent slack and a straight lay line. → Fluid lines: flares, flareless fittings and flexible hose
- Corrosion needs an anode, a cathode, an electrolyte and a conductive path, and the anodic metal is the one destroyed. → Corrosion: how it starts, the forms it takes and how to find it
- In AN bolt numbers, the first number is diameter in sixteenths of an inch, the dash number is grip in eighths, and a letter A means an undrilled shank. → Aluminum alloys, rivets, bolts, nuts, torque and safety wire
- Published torque values assume clean, dry threads, and a drive-end extension means the wrench must be set lower. → Aluminum alloys, rivets, bolts, nuts, torque and safety wire
Common trap
- Filiform questions swap the two humidity figures. The attack happens in the 78 to 90 percent band; 70 percent is the storage level that prevents it. → Corrosion: how it starts, the forms it takes and how to find it
- Oiling threads does not mean you need more torque. Published values assume clean, dry threads, and lubricant lets the same reading put far more tension into the bolt, so lubricate only where the maintenance data says to. → Aluminum alloys, rivets, bolts, nuts, torque and safety wire
Quick reference
| Line | How it is drawn | Meaning |
|---|---|---|
| Hidden | Short dashes, medium weight | An edge you cannot see from this view |
| Center | Thin long and short dashes | Center of a hole or symmetric part |
| Phantom | One long dash, two short dashes | Alternate position or adjacent part |
| Break | Ruled line with freehand zigzags | Part shortened on the drawing |
Chapter 5
Ground Operation, Servicing & Human Factors
Key takeaways
- Never use water on a burning magnesium wheel; blanket it with dry powder. → Fire protection on the ramp and during engine starts
- For fueling, ground the aircraft, ground the truck, bond the truck to the aircraft, then bond the nozzle, and remove in reverse order. → Fueling, oxygen servicing and turbine engine starts
- Treat every propeller as live, because a broken magneto P-lead leaves the magneto able to fire with the switch off. → Towing, taxi light signals and propeller safety
- Annual and 100-hour inspections use a checklist covering at least the scope and detail of part 43 appendix D. → Inspections and nondestructive testing methods
- After an interruption, go back at least three steps, and never release an aircraft with a tool unaccounted for. → Human factors: the Dirty Dozen and safety nets
Common trap
- Distractors offer CO2 or Halon for burning magnesium because they work on other fires. For a metal fire, the answer is dry powder, and water is always wrong. → Fire protection on the ramp and during engine starts
- For magnetic particle, the field must cross the crack. Cracks running along the part's length need circular magnetization, and a choice that says field direction does not matter, or that skips demagnetizing, is wrong. → Inspections and nondestructive testing methods
Quick reference
| Tower light, aircraft on the ground | Meaning |
|---|---|
| Flashing green | Cleared to taxi |
| Steady red | Stop |
| Flashing red | Taxi clear of the runway in use |
| Flashing white | Return to the starting point on the airport |
| Alternating red and green | Exercise extreme caution |
| Method | Works on | Finds |
|---|---|---|
| Visual | Any clean surface | Surface defects, with light at a low angle and a 10-power magnifier to confirm |
| Penetrant | Almost any nonporous material | Only flaws open to the surface |
| Magnetic particle | Ferromagnetic parts only | Flaws crossing the field; circular magnetization for lengthwise cracks; demagnetize after |
| Eddy current | Conductive materials | Surface and near-surface flaws, often through paint |
| Radiography | Parts the radiation can pass through, with radiation safety controls | Internal flaws, but not how deep they lie |