Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/23 ▾
  1. 1.Regulations, Records & Publications0/5
    1. What an A&P mechanic may do and approve
    2. Major or minor work, approved data and FAA Form 337
    3. Writing maintenance and inspection record entries
    4. Keeping records, AD status and inspection timing
    5. Keeping your mechanic certificate usable
  2. 2.Basic Electricity0/5
    1. Ohm's law, power and what sets a wire's resistance
    2. Series, parallel and series-parallel circuits
    3. Wire ratings, circuit protection and test meters
    4. Aircraft batteries and DC motors
    5. Alternating current, transformers and diodes
  3. 3.Weight & Balance, Math & Physics0/4
    1. Weight and balance terms: datum, empty weight, useful load and MAC
    2. Finding and correcting the center of gravity
    3. Shop mathematics: order of operations, areas, volumes and ratios
    4. Physics for aviation: power, levers, fluids, gases and stress
  4. 4.Materials, Hardware & Drawings0/4
    1. Reading aircraft drawings: lines, sections, tolerances and diagrams
    2. Fluid lines: flares, flareless fittings and flexible hose
    3. Corrosion: how it starts, the forms it takes and how to find it
    4. Aluminum alloys, rivets, bolts, nuts, torque and safety wire
  5. 5.Ground Operation, Servicing & Human Factors0/5
    1. Fire protection on the ramp and during engine starts
    2. Fueling, oxygen servicing and turbine engine starts
    3. Towing, taxi light signals and propeller safety
    4. Inspections and nondestructive testing methods
    5. Human factors: the Dirty Dozen and safety nets
Saved in this browser. Move it to another device →
← Back

Study guide · Chapter 4 of 5

Materials, Hardware & Drawings Study Guide — FAA A&P Mechanic (General)

40 free practice questions

This pool joins four ACS subjects a mechanic uses with a part in hand: reading drawings, making up fluid lines, controlling corrosion, and choosing and installing hardware. The questions test conventions and mechanisms more than memorized limits, and the real limits always come from current maintenance data. Learn why each rule exists and the distractors become easy to spot.

Key takeaways

  • Tolerance is the total of the plus and minus allowances, and a dimension's own limits override the general note in the title block.
  • A flexible hose shortens under pressure, so it is installed with 5 to 8 percent slack and a straight lay line.
  • Corrosion needs an anode, a cathode, an electrolyte and a conductive path, and the anodic metal is the one destroyed.
  • In AN bolt numbers, the first number is diameter in sixteenths of an inch, the dash number is grip in eighths, and a letter A means an undrilled shank.
  • Published torque values assume clean, dry threads, and a drive-end extension means the wrench must be set lower.

Lessons in this chapter

4 short lessons · 4 min read

  1. 1Reading aircraft drawings: lines, sections, tolerances and diagrams1 min
  2. 2Fluid lines: flares, flareless fittings and flexible hose1 min
  3. 3Corrosion: how it starts, the forms it takes and how to find it1 min
  4. 4Aluminum alloys, rivets, bolts, nuts, torque and safety wire1 min
View all questions & answers →

Facts checked 2026-11-15 · Sources: FAA-S-ACS-1 Aviation Mechanic Airman Certification Standards, FAA Aircraft Handbooks and Manuals (FAA-H-8083-30B AMT Handbook, General), FAA AC 43.13-1B Acceptable Methods, Techniques, and Practices: Aircraft Inspection and Repair

FAA A&P Mechanic (General) cheat sheet: every key fact on one page →Next chapter: Ground Operation, Servicing & Human Factors →

Practice tests

Practice questions based on 14 CFR Parts 43 and 65 and the FAA Aviation Maintenance Technician Handbook—General (FAA-H-8083-30). This site is not affiliated with or endorsed by the Federal Aviation Administration. This bank covers the GENERAL written test only; the Airframe and Powerplant written tests and the oral and practical exams are separate. Torque values, servicing quantities, corrosion rework limits, and inspection criteria always come from the manufacturer's current maintenance data and the applicable airworthiness directives — never from a practice test. Confirm current eligibility and testing requirements with the FAA before you test. About the A&P mechanic certificate →