Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/23 ▾
  1. 1.Regulations, Records & Publications0/5
    1. What an A&P mechanic may do and approve
    2. Major or minor work, approved data and FAA Form 337
    3. Writing maintenance and inspection record entries
    4. Keeping records, AD status and inspection timing
    5. Keeping your mechanic certificate usable
  2. 2.Basic Electricity0/5
    1. Ohm's law, power and what sets a wire's resistance
    2. Series, parallel and series-parallel circuits
    3. Wire ratings, circuit protection and test meters
    4. Aircraft batteries and DC motors
    5. Alternating current, transformers and diodes
  3. 3.Weight & Balance, Math & Physics0/4
    1. Weight and balance terms: datum, empty weight, useful load and MAC
    2. Finding and correcting the center of gravity
    3. Shop mathematics: order of operations, areas, volumes and ratios
    4. Physics for aviation: power, levers, fluids, gases and stress
  4. 4.Materials, Hardware & Drawings0/4
    1. Reading aircraft drawings: lines, sections, tolerances and diagrams
    2. Fluid lines: flares, flareless fittings and flexible hose
    3. Corrosion: how it starts, the forms it takes and how to find it
    4. Aluminum alloys, rivets, bolts, nuts, torque and safety wire
  5. 5.Ground Operation, Servicing & Human Factors0/5
    1. Fire protection on the ramp and during engine starts
    2. Fueling, oxygen servicing and turbine engine starts
    3. Towing, taxi light signals and propeller safety
    4. Inspections and nondestructive testing methods
    5. Human factors: the Dirty Dozen and safety nets
Saved in this browser. Move it to another device →
← Weight & Balance, Math & Physics

Chapter 3 · Lesson 4 of 4

Physics for aviation: power, levers, fluids, gases and stress

1 min read

  • Work = force × distance, and power = work / time. Example: lifting 1,100 lb through 15 ft in 10 seconds is 16,500 ft-lb, or 1,650 ft-lb per second, which is 1,650 / 550 = 3 horsepower.
  • Levers: in a third-class lever the effort is between the fulcrum and the load, so mechanical advantage is always less than 1, but the load moves farther and faster.
  • Pascal's law: pressure in a confined fluid is the same everywhere. Example: 50 lb on a 0.5 sq in piston makes 100 psi, which pushes a 4 sq in piston with 400 lb.
  • Bernoulli: in a venturi throat the air speeds up and its static pressure drops.

Gas laws need absolute units: add 14.7 to psig for psia, and add 460 to degrees F for degrees Rankine (−20 °F is 440 °R). Example: a sealed nitrogen bottle at 30 psig and 70 °F warms to 100 °F at constant volume.

P2 = 44.7 × 560 / 530 = 47.2 psia, which is about 32.5 psig. Stress questions name the load: tension pulls apart, compression crushes, shear slides layers past each other, and bending puts tension on the outside of the curve and compression on the inside at the same time.

Check yourself

1. An aircraft tire is inflated to 45 psig at 60 degrees F. If the tire is then heated to 120 degrees F and its volume does not change, what is the new gauge pressure?

2. Which statement correctly describes a third-class lever, such as a retractable landing gear actuated by a hydraulic cylinder?

Facts checked 2026-11-15 · Sources: FAA-S-ACS-1 Aviation Mechanic Airman Certification Standards, FAA Aircraft Handbooks and Manuals (FAA-H-8083-30B AMT Handbook General; FAA-H-8083-1 Weight and Balance Handbook)

FAA A&P Mechanic (General) cheat sheet: every key fact on one page →