Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/30 ▾
  1. 1.Models, Media & Topologies0/5
    1. The OSI and TCP/IP models: layers, data units and devices
    2. Copper and fiber: categories, distances and connectors
    3. Installing cable: plenum ratings and Power over Ethernet
    4. Wireless basics: channels, bonding, antennas and identifiers
    5. Topologies and network types: domains, mesh, spine and leaf, SAN
  2. 2.IP Addressing, Subnetting & Routing0/5
    1. IPv4 subnetting with the block-size method
    2. Private, loopback and APIPA ranges, and traffic types
    3. How routers choose a path: prefix, distance, metric and summaries
    4. IPv6: shortening, address types, SLAAC and NAT64
    5. VLANs, inter-VLAN routing and NAT
  3. 3.Ports, Protocols & Services0/5
    1. Well-known ports: secure and cleartext pairs
    2. TCP and UDP: handshake, flow control and real-time traffic
    3. DNS and DHCP: transports, records, relays and reservations
    4. Time and monitoring protocols: NTP and SNMP
    5. Tunnels, IPsec and QoS markings
  4. 4.Network Operations0/5
    1. Network documentation and the device lifecycle
    2. Monitoring with baselines, SNMP and syslog
    3. Seeing traffic: flow data, TAPs, mirror ports and availability checks
    4. Disaster recovery and high availability
    5. Change management and configuration baselines
  5. 5.Network Security0/5
    1. Core security terms: CIA, risk vocabulary and zero trust
    2. Identity and access: AAA, 802.1X, RADIUS, TACACS+, MFA and RBAC
    3. Filtering and segmentation: ACLs, screened subnets and IDS
    4. Recognizing network attacks from their symptoms
    5. Hardening, wireless authentication and physical security
  6. 6.Network Troubleshooting0/5
    1. The troubleshooting methodology, step by step
    2. Cable faults, distance limits, PoE budgets and the right tester
    3. Reading interface counters and port states
    4. Addressing and service failures: masks, DHCP, duplicates, loops, ACLs, DNS
    5. Wireless and voice quality problems
Saved in this browser. Move it to another device →
← Network Troubleshooting

Chapter 6 · Lesson 2 of 5

Cable faults, distance limits, PoE budgets and the right tester

1 min read

Twisted-pair Ethernet is specified for a 100 m channel, which the cabling standard divides into a 90 m permanent link plus up to 10 m of patch cords. Example: 80 m of horizontal cable plus a 3 m cord at each end is 86 m and fits; 115 m of horizontal cable alone does not.

Beyond the limit, attenuation drops the signal below the receiver's threshold, so the link becomes intermittent and error-prone under load rather than dead.

A split pair keeps continuity pin for pin, so a basic DC continuity tester calls it good. But the two wires of a signal come from different twisted pairs, the twist no longer cancels noise, and near-end crosstalk climbs at gigabit frequencies.

The link may settle at 100 Mbps or throw CRC errors at 1 Gbps. A certification tester, which measures crosstalk and other performance values, confirms it.

Power has its own limit. A PoE switch has a total wattage budget, so when cameras keep being added, the last ones fail to power on or reboot in a loop even though their cabling tests clean and they work on another switch. Check the switch's power status, not its VLANs or routes.

Check yourself

1. A new 1000BASE-T drop links intermittently and shows errors under load. The installer measured the horizontal cable run at 115 m from the patch panel to the wall jack, with a 3 m patch cord at each end; the cable is Category 6 and both terminations are correct. What is the best explanation?

2. A newly terminated Category 6 drop passes a basic DC continuity test with all eight conductors mapped straight through, pin for pin, and no opens or shorts. Yet the link only negotiates 100 Mbps, and when forced to 1 Gbps it produces continuous CRC errors. What is the most likely fault and which tool confirms it?

Facts checked 2026-11-16 · Sources: CompTIA Network+ certification overview, RFC 3927: Dynamic Configuration of IPv4 Link-Local Addresses

CompTIA Network+ cheat sheet: every key fact on one page →