Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/30 ▾
  1. 1.Models, Media & Topologies0/5
    1. The OSI and TCP/IP models: layers, data units and devices
    2. Copper and fiber: categories, distances and connectors
    3. Installing cable: plenum ratings and Power over Ethernet
    4. Wireless basics: channels, bonding, antennas and identifiers
    5. Topologies and network types: domains, mesh, spine and leaf, SAN
  2. 2.IP Addressing, Subnetting & Routing0/5
    1. IPv4 subnetting with the block-size method
    2. Private, loopback and APIPA ranges, and traffic types
    3. How routers choose a path: prefix, distance, metric and summaries
    4. IPv6: shortening, address types, SLAAC and NAT64
    5. VLANs, inter-VLAN routing and NAT
  3. 3.Ports, Protocols & Services0/5
    1. Well-known ports: secure and cleartext pairs
    2. TCP and UDP: handshake, flow control and real-time traffic
    3. DNS and DHCP: transports, records, relays and reservations
    4. Time and monitoring protocols: NTP and SNMP
    5. Tunnels, IPsec and QoS markings
  4. 4.Network Operations0/5
    1. Network documentation and the device lifecycle
    2. Monitoring with baselines, SNMP and syslog
    3. Seeing traffic: flow data, TAPs, mirror ports and availability checks
    4. Disaster recovery and high availability
    5. Change management and configuration baselines
  5. 5.Network Security0/5
    1. Core security terms: CIA, risk vocabulary and zero trust
    2. Identity and access: AAA, 802.1X, RADIUS, TACACS+, MFA and RBAC
    3. Filtering and segmentation: ACLs, screened subnets and IDS
    4. Recognizing network attacks from their symptoms
    5. Hardening, wireless authentication and physical security
  6. 6.Network Troubleshooting0/5
    1. The troubleshooting methodology, step by step
    2. Cable faults, distance limits, PoE budgets and the right tester
    3. Reading interface counters and port states
    4. Addressing and service failures: masks, DHCP, duplicates, loops, ACLs, DNS
    5. Wireless and voice quality problems
Saved in this browser. Move it to another device →
← Network Operations

Chapter 4 · Lesson 4 of 5

Disaster recovery and high availability

1 min read

TermMeaning
RPOMost data you may lose, measured back from the incident; sets backup frequency
RTOLongest the service may stay down; improved by faster restore or standby gear
MTBFAverage operating time between failures (reliability)
MTTRAverage time to repair a failed device (maintainability)

Availability equals MTBF divided by MTBF plus MTTR.

Example: MTBF of 2,000 hours and MTTR of 4 hours give 2,000 / 2,004, about 99.80%. Recovery sites trade cost for speed: a cold site is space, power and connectivity and takes days; a warm site has hardware and software installed and recovers in hours; a hot site is fastest and costs the most.

Active-active clusters share the load and must synchronize state, so each node must be able to carry the whole load; active-passive keeps an idle standby. A tabletop exercise only talks through the plan, so only a real restore or failover test proves the RPO and RTO. Hot and cold aisles keep exhaust air out of equipment intakes.

Check yourself

1. A business states that a failure of the order-processing system must never cost more than 15 minutes of transactions. Which recovery metric is being defined, and what does it primarily dictate?

2. Which metric is the average elapsed time required to restore a failed but repairable device to service, making it a measure of maintainability rather than of how often failures occur?

Facts checked 2026-11-16 · Sources: CompTIA Network+ certification overview, RFC 5424: The Syslog Protocol, NIST SP 800-34 Rev. 1: Contingency Planning Guide for Federal Information Systems

CompTIA Network+ cheat sheet: every key fact on one page →