Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/30 ▾
  1. 1.Models, Media & Topologies0/5
    1. The OSI and TCP/IP models: layers, data units and devices
    2. Copper and fiber: categories, distances and connectors
    3. Installing cable: plenum ratings and Power over Ethernet
    4. Wireless basics: channels, bonding, antennas and identifiers
    5. Topologies and network types: domains, mesh, spine and leaf, SAN
  2. 2.IP Addressing, Subnetting & Routing0/5
    1. IPv4 subnetting with the block-size method
    2. Private, loopback and APIPA ranges, and traffic types
    3. How routers choose a path: prefix, distance, metric and summaries
    4. IPv6: shortening, address types, SLAAC and NAT64
    5. VLANs, inter-VLAN routing and NAT
  3. 3.Ports, Protocols & Services0/5
    1. Well-known ports: secure and cleartext pairs
    2. TCP and UDP: handshake, flow control and real-time traffic
    3. DNS and DHCP: transports, records, relays and reservations
    4. Time and monitoring protocols: NTP and SNMP
    5. Tunnels, IPsec and QoS markings
  4. 4.Network Operations0/5
    1. Network documentation and the device lifecycle
    2. Monitoring with baselines, SNMP and syslog
    3. Seeing traffic: flow data, TAPs, mirror ports and availability checks
    4. Disaster recovery and high availability
    5. Change management and configuration baselines
  5. 5.Network Security0/5
    1. Core security terms: CIA, risk vocabulary and zero trust
    2. Identity and access: AAA, 802.1X, RADIUS, TACACS+, MFA and RBAC
    3. Filtering and segmentation: ACLs, screened subnets and IDS
    4. Recognizing network attacks from their symptoms
    5. Hardening, wireless authentication and physical security
  6. 6.Network Troubleshooting0/5
    1. The troubleshooting methodology, step by step
    2. Cable faults, distance limits, PoE budgets and the right tester
    3. Reading interface counters and port states
    4. Addressing and service failures: masks, DHCP, duplicates, loops, ACLs, DNS
    5. Wireless and voice quality problems
Saved in this browser. Move it to another device →
← Models, Media & Topologies

Chapter 1 · Lesson 2 of 5

Copper and fiber: categories, distances and connectors

1 min read

An Ethernet name such as 1000BASE-LX packs in three facts: the number is the speed in Mbps, BASE means baseband signaling (one signal uses the whole medium), and the suffix names the medium, so T is twisted pair and LX is a long-wavelength laser on fiber.

  • Twisted pair is built for a 100 m channel. 10GBASE-T reaches only about 55 m on Category 6 because of alien crosstalk; Category 6a carries it the full 100 m. Category 5e is not rated for 10GBASE-T, and Category 8 is short-reach data center cable of about 30 m.
  • Multimode fiber has a 50 or 62.5 micron core, so light takes many paths and pulses spread. Single-mode has an 8 to 9 micron core that carries one mode, letting a 1310 or 1550 nm laser go many kilometers. Neither fiber conducts electricity, so both ignore EMI.
  • LC, SC and ST each hold one fiber. MPO holds 12 or 24 fibers in one ferrule for parallel optics such as 40GBASE-SR4.
  • A direct attach copper (DAC) cable is twinax with transceivers fixed on both ends: the cheap choice for a few meters inside one rack.

Example: a new 10 Gbps drop must run 80 m across a floor. Category 6 tops out near 55 m at that speed, so specify Category 6a.

Check yourself

1. An installer must run 10GBASE-T links with a channel length of about 90 meters. Which statement about balanced twisted-pair cabling categories correctly explains the required choice?

2. In an Ethernet designation such as 1000BASE-LX, what does the 'BASE' portion of the name indicate?

Facts checked 2026-11-16 · Sources: CompTIA Network+ certification overview, RFC 1122: Requirements for Internet Hosts (TCP/IP layering)

CompTIA Network+ cheat sheet: every key fact on one page →