ASE Automotive Technician Cheat Sheet: Key Facts
Every key takeaway and common trap from the ASE Automotive Technician study guide on one page, grouped by chapter. Tap a lesson link to read the full explanation.
39 facts · 6 chaptersFacts checked 2026-11-16
Chapter 1
A1 — Engine Repair
Key takeaways
- If a low cylinder's compression rises sharply on the wet test, the leak is at the rings or cylinder wall, not a valve or head gasket. → Compression and cylinder leakage tests
- On a leakage test the place where air escapes names the leak: tailpipe means exhaust valve, intake means intake valve, oil fill means rings, coolant bubbles mean head gasket or crack. → Compression and cylinder leakage tests
- A pressure cap raises the coolant boiling point by roughly 3 °F per psi, so a weak cap causes boil-over under heavy load. → Lubrication and cooling system diagnosis
- Torque-to-yield head bolts are replaced, tightened in stages from the center outward, and finished with a specified angle. → Cylinder head, valve train and block measurements
- On a Technician A and B question, judge each statement on its own, and remember that both or neither can be the answer. → Lubrication and cooling system diagnosis
Common trap
- Technician A and Technician B questions: treat each technician's statement as its own true-or-false question. Decide whether A is right without looking at B, then judge B, then pick A only, B only, both, or neither. Both statements can be true, and both can be false, so neither is a real answer, not a filler. In the highway-overheating case above, a technician who blames the electric fan and one who blames a thermostat stuck open are both wrong. → Lubrication and cooling system diagnosis
- EXCEPT questions flip the task: three options are true and you are hunting for the false one. A common trick lists several real causes of low oil pressure and slips in a relief valve stuck closed, which raises pressure. Reread the stem before you answer. → Cylinder head, valve train and block measurements
Quick reference
| Where the air escapes (piston at TDC, compression stroke) | Leak path |
|---|---|
| Tailpipe | Exhaust valve not seating |
| Throttle body or intake | Intake valve not seating |
| Oil fill opening | Rings or cylinder wall |
| Bubbles in the coolant | Head gasket or a cracked head or block |
| Check | Correct method |
|---|---|
| Head warpage | Straightedge and feeler gauge, lengthwise and across both diagonals |
| Bearing clearance | Plastigage on a dry journal, cap torqued, crank not turned, width read on the wrapper scale |
| Bore taper and out-of-round | Dial bore gauge: top versus bottom of ring travel is taper; two readings 90° apart at one depth is out-of-round |
| Crankshaft end play | Dial indicator on the block, tip on the crank nose, crank pried fully each way |
Chapter 2
A5 — Brakes
Key takeaways
- A pedal that slowly sinks with no external leak and a normal fluid level points to fluid bypassing the master cylinder piston cups. → Master cylinder, brake lines and brake fluid
- Brake lines are replaced with steel tubing or approved copper-nickel tubing using double or ISO flares, never plain copper, aluminum, compression fittings or brazed patches. → Master cylinder, brake lines and brake fluid
- Brake pulsation is measured as rotor thickness variation with a micrometer, while lateral runout is read with a dial indicator. → Drum and disc brake service
- The thickness cast into a rotor is the discard limit, so a rotor below it is replaced. → Drum and disc brake service
- An amber ABS lamp alone means antilock is disabled but base braking still works; the red BRAKE lamp signals a base-system concern. → ABS, traction control and stability control
Common trap
- Dial indicator or micrometer? A dial indicator on the rotor face measures runout, the side-to-side wobble. Any question about thickness, thickness variation or minimum thickness needs a micrometer. Wrong answers often pair pulsation with runout because runout causes thickness variation over time, but it is not the direct measurement. → Drum and disc brake service
Quick reference
| Valve | What it does | Exam clue |
|---|---|---|
| Metering (hold-off) | Delays front pressure until the rear shoes overcome their return springs | No fluid at the front bleeders during pressure bleeding: hold the valve open |
| Proportioning | Limits rear pressure above a split point | Rear wheels lock first in a hard stop |
| Residual check | Keeps a few psi in a drum circuit so wheel cylinder cups stay sealed | Never used in a disc circuit, where it would cause drag |
Chapter 3
A6 — Electrical / Electronic Systems
Key takeaways
- In a series circuit current is the same everywhere and the largest resistance drops the most voltage; in parallel every branch gets full voltage and adding a branch raises total current. → Ohm's law, series and parallel circuits
- Voltage drop is measured with the circuit loaded, because a few thousandths of an ohm that an ohmmeter misses can waste most of a volt at starter current. → Voltage drop, shorts and parasitic draw
- A loaded charging circuit should lose only about 0.2 to 0.5 V between the generator output and the battery positive, so 0.7 V is excessive. → Voltage drop, shorts and parasitic draw
- A rested battery reads about 12.6 V when full and about 12.2 V at half charge, and it must be fully charged before a load test means anything. → Battery, starting and charging systems
- Never connect an ohmmeter to an airbag deployment loop, because its test current can fire the inflator. → Voltage drop, shorts and parasitic draw
Common trap
- Fast flashing after an LED swap is not a bad flasher. LEDs draw far less current than incandescent bulbs, so a load-sensing flasher or outage monitor thinks a bulb has failed. The fix is load resistors or hardware designed for LED current, not a heavier relay or bigger wire. → Lighting system diagnosis
Chapter 4
A4 — Suspension & Steering
Key takeaways
- A vehicle pulls toward the side with more positive camber and toward the side with less positive caster. → Wheel alignment angles and pull diagnosis
- A feathered, saw-tooth tread edge means toe is wrong; camber wears one shoulder, and caster causes no tire wear. → Wheels, tires, balance and TPMS
- On a hydraulic system, if pressure reaches specification with the shutoff valve briefly closed but is low at the stops, the steering gear is leaking internally. → Power steering systems and steering gears
- A wheel bearing growl gets louder when the turn loads it, so noise in a left turn points to the right-side bearing. → Suspension inspection and service
- After any toe change, relearn the steering angle sensor and aim any forward camera as the manufacturer specifies. → Wheel alignment angles and pull diagnosis
Common trap
- Not every pull is an alignment problem. A vehicle that tracks straight but pulls only while braking has a brake imbalance, and it pulls toward the side that is still braking well, away from a seized caliper or restricted hose. And an alignment is not finished when the angles are in range: the steering angle sensor relearn and any camera aiming the maker specifies still have to be done. → Wheel alignment angles and pull diagnosis
Quick reference
| Tire wear pattern | Angle that causes it |
|---|---|
| Feathered, saw-tooth edges across the ribs | Toe |
| One shoulder worn smooth | Camber |
| No wear pattern | Caster |
Chapter 5
A8 — Engine Performance
Key takeaways
- Before clearing anything, read pending codes and freeze frame, because clearing erases that evidence and resets readiness monitors. → The diagnostic process and on-board diagnostic data
- Fuel trim that is high at idle and near zero at cruise points to an unmetered air leak; a problem on one bank only cannot be the airflow sensor. → Fuel trim, fuel delivery and air induction
- In a part-swap test, a fault that follows the part condemns the part, and a fault that stays with the cylinder clears it. → Engine mechanical and ignition testing
- A wideband air/fuel sensor reports the actual mixture by varying its pump cell current, so it does not switch like a zirconia sensor. → Emissions controls and engine sensors
- A flashing check engine lamp means a misfire severe enough to damage the catalytic converter, so reduce load and stop driving until it is repaired. → Engine mechanical and ignition testing
Common trap
- Do not judge a wideband air/fuel sensor like a zirconia oxygen sensor. A conventional sensor makes a 0 to 1 volt signal that switches across about 0.45 V; a wideband sensor varies its pump cell current to report the actual ratio, and many scan tools show a steady value or a lambda near 1.00 while the engine is in control. A steady reading there is normal, not a dead sensor. → Emissions controls and engine sensors
Chapter 6
A7 — Heating & Air Conditioning
Key takeaways
- Identify refrigerant before recovery, and send any mixture into a separate cylinder for contaminated refrigerant, never into the recycling machine and never into the air. → Refrigerant identification, recovery and EPA rules
- Evacuation removes air and moisture but not solid debris, which has to be flushed out or removed by replacing parts. → Flushing, evacuation, charging and compressor oil
- Both gauges low points to an undercharge, a high high side points to air, overcharge or poor condenser airflow, and a high low side with a low high side points to the compressor. → Reading gauge pressures and locating components
- Full voltage at the clutch coil with no engagement means an open coil or a bad ground, not a fuse, switch or diode. → Compressor clutch controls and blower speed circuits
- An open NTC temperature sensor reads as extremely cold, so an automatic system drives toward full heat. → Automatic climate sensors, weak heat and coolant electrolysis
Common trap
- An adapter that lets one machine connect to another refrigerant's port is never the legal answer, even when the machine itself is certified. → Refrigerant identification, recovery and EPA rules
- EXCEPT questions list three causes of the same reading and one that produces the opposite. Leaking reed valves lower the high side, so they are the exception in a list of high head pressure causes. → Reading gauge pressures and locating components
- No clutch engagement while the engine is overheating is normal load-sensitive control, not an HVAC fault; fix the overheating, not the clutch. → Compressor clutch controls and blower speed circuits
Quick reference
| Low side | High side | Likely cause |
|---|---|---|
| Low | Low | Undercharge: the evaporator is starved and there is too little vapor to build head pressure |
| Normal or high | High | Air in the system, overcharge, or poor condenser airflow such as a dead fan |
| High | Low | Compressor not pumping, such as leaking reed valves |