Quibank app: now on the App Store — free, works offline. Get the app ↗

Chapters0/38 ▾
  1. 1.Safety, PPE, SCBA & Communications0/5
    1. Two-in/two-out and personnel accountability
    2. Maydays, emergency traffic and radio discipline
    3. Turnout gear: layers, inspection, retirement and decon
    4. SCBA readiness, air management and emergencies
    5. PASS devices and roadway scene safety
  2. 2.Fire Behavior & Building Construction0/5
    1. The fire tetrahedron, fuel properties and toxic smoke
    2. Heat transfer and reading smoke
    3. Ventilation-limited fires and hostile fire events
    4. Flow paths, closed doors and applying water
    5. Construction types and collapse hazards
  3. 3.Ground Ladders & Forcible Entry0/4
    1. Ladder parts, materials and service testing
    2. Climbing angle, tip placement and power lines
    3. Forcible entry tools and their care
    4. Forcing doors, locks, glass and roll-up gates
  4. 4.Search & Rescue and Ventilation0/4
    1. Primary and secondary search
    2. Moving victims, downed firefighters and VEIS
    3. Flow paths, door control and timing ventilation
    4. Horizontal, PPV, hydraulic and vertical ventilation
  5. 5.Water Supply, Hose, Streams & Extinguishers0/5
    1. Hydrants, water pressure and drafting
    2. Supply hose lays, hose loads and appliances
    3. Hose couplings, rolls and hose care
    4. Fire streams: nozzle pressure, steam and friction loss
    5. Portable extinguishers: classes, ratings and PASS
  6. 6.Fire Control, Overhaul, Ropes & Knots0/5
    1. Life safety rope, utility rope and rope care
    2. Knots and hoisting tools and hoselines
    3. Interior fire attack: direct, indirect and below-grade fires
    4. Vehicle, grass and flammable gas fires
    5. Property conservation and overhaul
  7. 7.Firefighter II Operations0/5
    1. Command and the Incident Command System
    2. Foam, flammable liquids and BLEVE prevention
    3. Sprinklers, standpipes and smoke alarms
    4. Fire cause, evidence and incident reports
    5. Airbag clearance, thermal imaging and hose testing
  8. 8.Hazmat Awareness & Operations0/5
    1. Response levels, training and a safe approach
    2. Placards, NFPA 704 and container shapes
    3. Using the Emergency Response Guidebook
    4. Product behavior, defensive control and public protection
    5. Control zones, decontamination and protection levels
Saved in this browser. Move it to another device →
← Water Supply, Hose, Streams & Extinguishers

Chapter 5 · Lesson 1 of 5

Hydrants, water pressure and drafting

Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.

1 min read

Exam questions about water supply start with three pressure words. Static pressure is the reading in the main when no water is moving. Residual pressure is what is left in the system while water flows.

Velocity, or pitot, pressure is the forward push of a stream measured with a pitot gauge at an open outlet. Elevation pressure has to do with height, not flow. For example, if a capped hydrant reads 80 psi at rest and 62 psi while a neighboring hydrant flows, 80 is static and 62 is residual.

While pumping from a hydrant, the operator stops adding flow when the intake residual falls toward about 20 psi. Going lower can damage the main, draw contaminants back into drinking water and starve other users.

Dry-barrel hydrants, used where winters freeze, are opened fully and slowly: the drain stays open whenever the main valve is only partly open, so a half-open hydrant pushes water out the drain and washes away the soil around it. When there is no hydrant, an engine drafts from a pond or tank through hard suction hose, which stays rigid under vacuum; soft sleeve hose would collapse.

Bonnet color (NFPA)ClassRated flow
Light blueAA1,500 gpm or more
GreenA1,000 to 1,499 gpm
OrangeB500 to 999 gpm
RedCUnder 500 gpm

Check yourself

1. During a hydrant flow test, a cap gauge on the test hydrant reads 72 psi with no water moving and 58 psi while a nearby hydrant flows. What does the 58 psi reading represent?

2. An engine is pumping from a hydrant, and the operator watches the intake gauge fall as more lines are opened. Below about what residual pressure should the operator stop increasing flow to protect the water system?

Facts checked 2026-11-15 · Sources: NFPA 1010 (2024): Professional Qualifications for Firefighters, NFPA 10: Standard for Portable Fire Extinguishers, NFPA 1930 (2025): fire service use of ground ladders, fire hose and other equipment

Firefighter I & II Certification cheat sheet: every key fact on one page →