Firefighter I & II Certification Cheat Sheet: Key Facts
Varies by state. Your state sets this exam: the number of questions, time limit, pass mark and any state-law section can differ from this practice. Check your state's official handbook or licensing board before you test.
Every key takeaway and common trap from the Firefighter I & II Certification study guide on one page, grouped by chapter. Tap a lesson link to read the full explanation.
60 facts · 8 chaptersFacts checked 2026-11-15
Chapter 1
Safety, PPE, SCBA & Communications
Key takeaways
- For an interior attack in an IDLH atmosphere, at least two firefighters go in together and at least two equipped firefighters stay outside ready to rescue, unless a life is in imminent danger. → Two-in/two-out and personnel accountability
- Call a mayday the moment you are lost, trapped or in trouble, then give location, unit, name, air and needs. → Maydays, emergency traffic and radio discipline
- Structural turnout gear is retired no more than 10 years after manufacture, no matter how it looks, and gets an advanced inspection at least every 12 months. → Turnout gear: layers, inspection, retirement and decon
- Under the Rule of Air Management you leave the hazard area before the low-air alarm sounds, so the alarm is a backup, not the signal to start out. → SCBA readiness, air management and emergencies
- A PASS goes into alarm when the wearer stops moving; integrated units arm when the cylinder is opened, stand-alone units must be switched on by hand. → PASS devices and roadway scene safety
Common trap
- Waiting is the wrong answer in mayday questions. Options that say call after the low-air alarm, after the PASS sounds, or after searching alone for a while all burn the air a rescue depends on. → Maydays, emergency traffic and radio discipline
- Two classic mix-ups: swapping the inner layers (the thermal liner is innermost, not the moisture barrier), and believing that gear in good condition can stay in service past 10 years. Age alone retires it. → Turnout gear: layers, inspection, retirement and decon
- Do not treat the low-air alarm as the cue to leave. Answers like as soon as the low-air alarm sounds or when the gauge reads empty are wrong; the plan is to be out before the alarm. → SCBA readiness, air management and emergencies
Quick reference
| Care step (NFPA 1850) | When |
|---|---|
| Routine inspection | After every use |
| Advanced inspection by a trained person | At least every 12 months, or whenever damage is suspected |
| Retirement | No more than 10 years after the date of manufacture |
Chapter 2
Fire Behavior & Building Construction
Key takeaways
- Water mainly cools, smothering removes oxygen, fuel removal separates fuel, and dry chemical mainly breaks the chemical chain reaction. → The fire tetrahedron, fuel properties and toxic smoke
- A closed-up fire that looks like it is dying is usually ventilation-limited, and any new opening, even the entry door, can make it grow fast. → Ventilation-limited fires and hostile fire events
- Backdraft needs air added to a hot, sealed, fuel-rich space; a smoke explosion is premixed smoke igniting, often in a void after knockdown. → Ventilation-limited fires and hostile fire events
- UL FSRI found that water applied into the fire area did not push fire into other rooms, and that a closed door keeps a room survivable much longer. → Flow paths, closed doors and applying water
- Set a collapse zone of at least 1.5 times the wall height, and expect fast, unannounced failure from lightweight trusses and unprotected steel. → Construction types and collapse hazards
Common trap
- Backdraft and smoke explosion are the most swapped pair. Ask whether air had to be added to a hot, sealed space (backdraft) or whether the smoke was already mixed with air and just met a spark (smoke explosion). → Ventilation-limited fires and hostile fire events
- Noncombustible does not mean fire-resistive. A II(000) building has no required fire-resistance rating at all, and the digits say nothing about sprinklers or contents. → Construction types and collapse hazards
Quick reference
| Term | Meaning |
|---|---|
| Flash point | Lowest temperature where vapor ignites briefly with an outside flame |
| Fire point | Slightly higher; burning continues once ignited |
| Autoignition temperature | Ignites with no outside flame at all |
| Vapor density above 1 | Heavier than air; sinks to drains, pits and basements |
| Event | What happens and key clue |
|---|---|
| Rollover (flameover) | Flames roll through the ceiling gas layer while contents below are unburned; flashover may be near |
| Flashover | Nearly all exposed surfaces ignite at once from radiant heat off the upper layer |
| Backdraft | Air enters a hot, sealed, oxygen-starved space; clues are puffing smoke, dark-stained windows, little flame |
| Smoke explosion | Cooler smoke already mixed with air ignites, often in a void away from the fire, even after knockdown |
Chapter 3
Ground Ladders & Forcible Entry
Key takeaways
- Ground ladders are service tested at least once a year and again after heat exposure, overloading, damage or repair. → Ladder parts, materials and service testing
- For about a 75° climbing angle, set the butt one quarter of the working length in use away from the wall. → Climbing angle, tip placement and power lines
- The tip goes several rungs above a roof edge for roof access, but just below or even with the sill for a window rescue. → Climbing angle, tip placement and power lines
- Strike a Halligan only with a flat-head axe or another striking tool, never with a pick-head axe. → Forcible entry tools and their care
- Tempered glass shatters into small cubes, laminated glass cracks but stays in one sheet and must be cut. → Forcing doors, locks, glass and roll-up gates
Common trap
- In 1:4 questions, divide the length actually in use, not the designated length printed on the ladder. And wrong answers on fiberglass claim it never conducts; it can, when wet or dirty. → Climbing angle, tip placement and power lines
- Category questions hide the answer in what the tool does, not what it looks like. A pike pole or drywall hook pushes and pulls, not pries, and a pick-head axe is never the striking tool for the irons. → Forcible entry tools and their care
Quick reference
| Job | Tip placement |
|---|---|
| Roof access | Several rungs (commonly 3 to 5) above the roof edge, for handholds and to be found in smoke |
| Window rescue | Just below or even with the sill, so the whole opening stays clear |
| Category | Examples |
|---|---|
| Prying | Halligan bar, pry bar |
| Striking | Flat-head axe, sledgehammer |
| Pushing/pulling | Pike pole, drywall hook, plaster hook |
| Cutting | Rotary saw, bolt cutters |
Chapter 4
Search & Rescue and Ventilation
Key takeaways
- The primary search is fast but thorough during suppression and starts nearest the fire; the secondary search is slow and methodical after control, ideally by a fresh crew. → Primary and secondary search
- On a hoseline, the female coupling side leads back toward the water source and the way out. → Primary and secondary search
- In VEIS, the first action after entering through the window is to close the room's door. → Moving victims, downed firefighters and VEIS
- Ventilation is timed for when a charged line is ready to flow, because new openings feed a ventilation-limited fire. → Flow paths, door control and timing ventilation
- Vertical openings go as high as safely possible directly over the fire; a trench cut comes later as a defensive break. → Horizontal, PPV, hydraulic and vertical ventilation
Common trap
- In VEIS questions, the tempting answer is to search the bed first because a victim may be there. Isolate comes before search: shut the door first, or the room can become the fire's exhaust. → Moving victims, downed firefighters and VEIS
- Answers that say vent early so conditions improve, or open everything so heat escapes, reflect old thinking. Without water ready, added air makes the fire grow. → Flow paths, door control and timing ventilation
Quick reference
| Method | Key rule |
|---|---|
| Natural horizontal | Open the downwind (leeward) exhaust first, then the upwind (windward) intake |
| Positive-pressure (PPV) | Exhaust opening near the fire first; fan outside the door so its cone covers the doorway |
| Hydraulic | Fog covering about 85 to 90 percent of the window, nozzle about 2 ft back (IFSTA) |
| Vertical | As high as safely possible, directly over the fire |
Chapter 5
Water Supply, Hose, Streams & Extinguishers
Key takeaways
- Static pressure is read with no water flowing, residual pressure is what remains while water flows, and an engine on a hydrant should keep at least about 20 psi residual. → Hydrants, water pressure and drafting
- A forward lay leaves the engine at the fire, a reverse lay leaves it at the water source, and a siamese combines lines while a wye splits them. → Supply hose lays, hose loads and appliances
- Common nozzle pressures are about 50 psi for smooth-bore handlines, 80 psi for smooth-bore master streams and 100 psi for fog nozzles. → Fire streams: nozzle pressure, steam and friction loss
- Friction loss rises with the square of the flow, so doubling the flow roughly quadruples the loss, while elevation adds about 0.5 psi per foot. → Fire streams: nozzle pressure, steam and friction loss
- Match the extinguisher to the fuel: nonconductive agents for energized electrical fires, Class D powder for metals and Class K wet chemical for cooking oil. → Portable extinguishers: classes, ratings and PASS
Common trap
- Do not mix up Storz and threaded features. Distractors attach a Higbee cut or a double-male adapter to Storz couplings, or claim the Higbee notch shows a passed service test. The notch only marks where the thread starts. → Hose couplings, rolls and hose care
- When flow doubles, the tempting answer is that friction loss doubles. It does not; it roughly quadruples. Only a change in hose length scales the loss one-for-one. → Fire streams: nozzle pressure, steam and friction loss
- Two look-alike words catch many test takers. Dry chemical (ABC) and dry powder (Class D) are different agents, and only dry powder is meant for burning metals. Also watch for answers that aim at the top of the flames or into the smoke; PASS always aims at the base, where the fuel is burning. → Portable extinguishers: classes, ratings and PASS
Quick reference
| Bonnet color (NFPA) | Class | Rated flow |
|---|---|---|
| Light blue | AA | 1,500 gpm or more |
| Green | A | 1,000 to 1,499 gpm |
| Orange | B | 500 to 999 gpm |
| Red | C | Under 500 gpm |
| Nozzle | Typical operating pressure |
|---|---|
| Smooth-bore handline | About 50 psi |
| Smooth-bore master stream | About 80 psi |
| Fog nozzle (standard) | About 100 psi |
| Fire class | Fuel | Right agent |
|---|---|---|
| C | Energized electrical equipment | Nonconductive agent such as CO2 |
| D | Combustible metals such as magnesium | Class D dry powder |
| K | Cooking oils and fats | Wet chemical |
Chapter 6
Fire Control, Overhaul, Ropes & Knots
Key takeaways
- Any rope that supports a person is life safety rope, and a life safety rope that is shock-loaded is removed from life safety service even if it looks fine. → Life safety rope, utility rope and rope care
- Hoist tools with a clove hitch plus half hitches and a tag line, and hoist a charged line only with the nozzle shut and secured. → Knots and hoisting tools and hoselines
- Use an indirect attack only when no victims or crews are in the space, and open and close nozzles slowly to prevent water hammer. → Interior fire attack: direct, indirect and below-grade fires
- Approach a car fire from the side at about 45 degrees, upwind and uphill, and attack a grass fire from an anchor point along the flanks. → Vehicle, grass and flammable gas fires
- Keep SCBA on during overhaul until air monitoring shows the area is safe, and leave possible evidence in place for the investigator. → Property conservation and overhaul
Common trap
- Wrong answers suggest keeping a shock-loaded rope because it looks undamaged, washing it, or waiting for the next annual inspection. None of these restores or proves the strength of the core. → Life safety rope, utility rope and rope care
- Watch for answers that meet the danger head-on: approaching a car from the front or rear, attacking a grass fire at the head or from downhill, or blowing out a gas flame before the valve is shut. The safe answer works from the side and removes the fuel source first. → Vehicle, grass and flammable gas fires
- In overhaul questions, the tempting answers sound efficient: take off SCBA once the smoke looks clear, flood the area with a big stream, or shovel suspicious debris outside. Clear air is not safe air, extra water is extra damage, and moving evidence destroys what investigators need. → Property conservation and overhaul
Quick reference
| Knot | Main use |
|---|---|
| Bowline | Forms a fixed loop |
| Clove hitch | Attaches rope to an object such as a tool handle |
| Half hitch | Used with another knot to keep a long object aligned |
| Becket (sheet) bend | Joins ropes of unequal diameter, or rope to webbing or chain |
| Water knot | Joins webbing |
Chapter 7
Firefighter II Operations
Key takeaways
- Command transfers only by a deliberate, preferably face-to-face briefing, never automatically when a higher rank arrives. → Command and the Incident Command System
- ICS span of control is 3 to 7 per supervisor with 5 as the optimum; divisions are geographic and groups are functional. → Command and the Incident Command System
- A foam percentage is the share of concentrate in the solution, and polar solvents such as ethanol need alcohol-resistant concentrate. → Foam, flammable liquids and BLEVE prevention
- On an OS&Y valve a visible, extended stem means open, and a Class I standpipe gives the fire department 2½-inch outlets. → Sprinklers, standpipes and smoke alarms
- Firefighters recognize and protect possible evidence and report it, while the investigator documents, collects and decides the cause. → Fire cause, evidence and incident reports
Common trap
- Rank is not a handoff. Answers saying command passes the moment a chief arrives, or by a name-only radio call or a note, are wrong because the new commander gets no briefing. → Command and the Incident Command System
- Numbers in this section are easy to swap. Distractors use the driver's 10 inches for the passenger airbag, call 7 the optimum span of control, or test hose at the pump's maximum pressure or in 500-foot lines. Tie each number to its reason: biggest bag, middle of the range, one test pressure per marking, shorter lines. → Airbag clearance, thermal imaging and hose testing
Quick reference
| ICS term | What it means |
|---|---|
| Command Staff | Safety Officer, Public Information Officer, Liaison Officer |
| General Staff | Section chiefs for Operations, Planning, Logistics, Finance/Administration |
| Division | Resources in one geographic area, such as a floor or side |
| Group | Resources doing one function anywhere on the incident |
| Sprinkler system | How it works |
|---|---|
| Wet-pipe | Water in the pipes at all times |
| Dry-pipe | Air in the pipes; a fused head drops the air pressure and lets water in |
| Pre-action | Air in the pipes; a separate detection system fills them, and water flows only where a head has fused |
| Deluge | Open heads that all flow at once |
Chapter 8
Hazmat Awareness & Operations
Key takeaways
- Awareness responders recognize, isolate, deny entry, protect and notify; Operations responders add defensive actions from a distance; plugging and patching is Technician work. → Response levels, training and a safe approach
- Approach uphill, upwind and upstream, and never treat a missing placard as proof that a load is safe. → Response levels, training and a safe approach
- In the ERG, yellow pages sort by ID number, blue by name, orange hold the guides, and green give distances for highlighted materials when there is no fire. → Using the Emergency Response Guidebook
- Level B, with SCBA, is the minimum protection when the hazards are not yet identified. → Control zones, decontamination and protection levels
- Decon goes in the warm zone, upwind and uphill of the hot zone, and mass decon uses high-volume, low-pressure water. → Control zones, decontamination and protection levels
Common trap
- Many wrong answers sound helpful but exceed the responder's level. If an option touches the container (plug, patch, tighten, overpack), it is Technician work, not Awareness or Operations. → Response levels, training and a safe approach
- Two placard traps: assuming no placard means no hazard (Table 2 loads under 1,001 lb ride unplacarded), and reading the NFPA 704 scale backward. A 4 is the most severe rating, never the least. → Placards, NFPA 704 and container shapes
- Do not use green-table distances for a burning load. Green distances are for spills without fire; fire sends you to the orange guide's evacuation distance. → Using the Emergency Response Guidebook
Quick reference
| Level | What it may do |
|---|---|
| Awareness | Recognize the hazard, isolate the area, deny entry, protect self and others, notify authorities; no control of the release |
| Operations | Defensive actions from a safe distance, such as diking, damming and diverting, without touching the leak |
| Technician | Offensive work at the source: plugging, patching, tightening valves, overpacking |
| Section | Use |
|---|---|
| Yellow pages | Index by 4-digit UN/NA ID number; points to a 3-digit guide |
| Blue pages | Index alphabetically by material name; points to a guide |
| Orange pages | The response guides: hazards, public safety, fire evacuation distances |
| Green pages | Isolation and protective action distances for highlighted materials, spills without fire |