22 Ground Ladders & Forcible Entry Practice Questions & Answers
Every Ground Ladders & Forcible Entry practice question from the Firefighter I & II Certification Practice Test, with the correct answer and a short explanation.
Start practice test →1. Under NFPA's requirements for the care and service testing of in-service fire department ground ladders, at a minimum, how often must in-service ladders be service tested?
- A.Only after visible damage
- B.Only at initial acceptance
- C.Once a year at a minimum✓ Answer
- D.Once every five years
The use-and-maintenance side of the NFPA ground-ladder standard requires service testing at least annually, because hidden weakening from heat, loading and age is not always visible. Extra tests are also required after overloading, heat exposure, damage or repair, but those triggers add to the yearly test rather than replace it. Acceptance testing of a new ladder is a separate step, and a five-year interval is far too long.
Ref QB-UC5EFWSource: NFPA 1932 in-service ground ladders (consolidated into NFPA 1930, 2025 edition) — annual service testingReport a problem with this question
2. A Fire Fighter I candidate is assigned to force entry into a locked structure. Under the NFPA forcible entry job performance requirement, the task is complete when the firefighter has:
- A.breached the barrier within a fixed two-minute limit
- B.opened the barrier while using only a single hand tool
- C.taken the door completely off its hinges and frame
- D.removed the barrier and left the opening safe for entry✓ Answer
The Fire Fighter I forcible entry JPR is written around an outcome: the barrier is removed and the opening is left in a condition that is safe for crews to enter. The standard does not set a tool count or a stopwatch time, and pulling a door completely off its frame is not required; often the least-damaging method that still gets crews in quickly is preferred.
Ref QB-BVX8VVSource: NFPA 1010 (2024), Fire Fighter I — forcible entry JPR (formerly NFPA 1001 Fire Fighter I)Report a problem with this question
3. A firefighter extends the fly section of an extension ladder and lets it settle. Which component engages a bed-section rung to hold the fly at that height?
- A.Fly guides
- B.Halyard rope
- C.Pawl locks✓ Answer
- D.Fly stops
Pawls, also called dogs or ladder locks, are hooks mounted on the fly that swing over a bed-section rung and lock the fly at the chosen height. The halyard only raises and lowers the fly, the guides keep the sections aligned as they slide, and the stops keep the fly from being pulled out past full extension.
Ref QB-TCS3AVSource: NFPA 1932 (now NFPA 1930) ground-ladder terminology — pawls (ladder locks)Report a problem with this question
4. During a post-fire check, a firefighter sees that the heat-sensor label on the inside of a beam near the tip of a ladder has changed color. What should be done with the ladder?
- A.Remove it from service until it passes a service test✓ Answer
- B.Replace the label and return the ladder to the apparatus
- C.Keep it in service unless the beams look visibly warped
- D.Limit it to light duty until the next annual inspection
Heat-sensor labels change color at roughly 300°F (149°C), a temperature at which aluminum and other ladder materials can lose strength without visible signs. A changed label means the ladder must come out of service and pass a service test before anyone uses it again; swapping the label or relying on a visual check hides possible internal damage.
Ref QB-AVKWPUSource: NFPA 1932 (now NFPA 1930) — heat-sensor label activation requires removal from service and service testingReport a problem with this question
5. A crew is choosing a ladder to work near energized electrical equipment on a rainy night. Which statement about fiberglass ground ladders is correct?
- A.They should be fully painted to protect the resin
- B.They can conduct electricity when wet or dirty✓ Answer
- C.They are unaffected by long exposure to sunlight
- D.They stay nonconductive in every weather condition
Fiberglass is nonconductive only when it is clean and dry; water, dirt and contamination on the surface can carry current, so no ground ladder should be treated as safe around energized equipment. Fiberglass is also degraded by ultraviolet light and impact, and painting a ladder hides defects rather than protecting it.
Ref QB-SCER4USource: NFPA 1010 (2024), Fire Fighter I — ground ladders; ladder material characteristics (fiberglass conductivity when wet or dirty)Report a problem with this question
6. A 24-ft extension ladder is fully extended and set at the proper climbing angle against a wall. How does its vertical reach compare with its designated length?
- A.Exactly equal to 24 ft
- B.Slightly less than 24 ft✓ Answer
- C.Slightly more than 24 ft
- D.About half of the 24 ft
Designated length is measured along the beams, but a ladder set at about 75° leans away from the wall, so its vertical reach is a little shorter than its length. Common guidance is about 1 ft less reach for ladders of 35 ft or shorter (about 2 ft less for longer ones), which is why a ladder must be chosen slightly longer than the height it has to reach.
Ref QB-9V8KHTSource: NFPA 1010 (2024), Fire Fighter I — ground ladders; designated length vs. working reach at ~75° climbing angleReport a problem with this question
7. A crew is laddering a building so firefighters can step off onto the roof. How should the ladder tip be positioned relative to the roof edge?
- A.Extended several rungs above the roof edge✓ Answer
- B.Laid back flat on the roof beyond the gutter
- C.Set exactly flush with the top of the gutter
- D.Set just below the roof edge, out of sight
For roof access the tip is extended several rungs (commonly about 3 to 5) above the roof edge so firefighters have handholds while stepping on and off, and so crews on the roof can see and find the ladder in smoke. A tip set flush with or below the edge gives nothing to hold and is easy to lose sight of.
Ref QB-RC3EXSSource: NFPA 1010 (2024), Fire Fighter I — ground ladders; tip placement for roof accessReport a problem with this question
8. A victim at a second-floor window will be brought down a ground ladder by firefighters. Where should the ladder tip be placed?
- A.Just below or even with the windowsill✓ Answer
- B.Several rungs above the top of the window
- C.Beside the window on the windward side
- D.Inside the room, resting on the floor
For rescue the tip goes just below or even with the sill so the full width of the window stays clear and the victim can be moved straight from the sill onto the ladder. A tip above the opening blocks the window, a tip off to one side is a different placement used for other tasks, and pushing the tip into the room makes it hard to get the victim onto the rungs.
Ref QB-8VV8CSSource: NFPA 1010 (2024), Fire Fighter I — ground ladders; tip placement for rescue from a windowReport a problem with this question
9. A 35-ft extension ladder is raised against a building, but only 28 ft of its length is in use. Using the 1:4 rule for a proper climbing angle, about how far from the wall should the butt be?
- A.About 4 ft
- B.About 9 ft
- C.About 14 ft
- D.About 7 ft✓ Answer
The 1:4 rule divides the working length actually in use by 4 to give the butt distance that produces about a 75° angle: 28 ÷ 4 = 7 ft. Dividing the 35-ft designated length instead gives about 9 ft, a common mistake that sets the ladder too flat; 14 ft is half the length and would be dangerously shallow.
Ref QB-QCQ3SRSource: NFPA 1010 (2024), Fire Fighter I — ground ladders; 1:4 butt-distance rule (~75° climbing angle)Report a problem with this question
10. Before raising any ground ladder near overhead electrical wires, what is the minimum clearance firefighters are taught to keep between the ladder and the lines?
- A.3 ft (1 m)
- B.2 ft (0.6 m)
- C.6 ft (2 m)
- D.10 ft (3 m)✓ Answer
Fire service training sets at least 10 ft (3 m) of clearance from overhead power lines at every point of the raise, because electricity can arc across a gap and a swinging ladder can easily close a smaller margin. Firefighters look up before raising, and the rule applies to every ladder material, since wet or dirty wood and fiberglass can conduct.
Ref QB-QMM88SSource: NFPA 1010 (2024), Fire Fighter I — ground ladders; overhead power-line hazard (10 ft / 3 m minimum clearance)Report a problem with this question
11. Two firefighters disagree about whether the fly section of an extension ladder should face toward or away from the building. What should decide the orientation?
- A.Always fly out, facing toward the climber
- B.The ladder manufacturer's recommendation✓ Answer
- C.The side where the halyard happens to hang
- D.Always fly in, against the building wall
Fly orientation depends on how the ladder was designed and tested, so the manufacturer's recommendation governs. Many current aluminum and fiberglass ladders are built for fly out, while many wood ladders were designed for fly in, which is why neither blanket rule is correct; the side the halyard hangs on is a result of the setup, not a reason for it.
Ref QB-85TDTSSource: NFPA 1932 (now NFPA 1930) — use ground ladders per manufacturer's instructions; fly orientationReport a problem with this question
12. An extension ladder has just been raised and extended against a wall. Before anyone climbs it, which check is essential?
- A.The halyard is removed from its pulley
- B.The fly is left unlocked so it can adjust
- C.The butt spurs are lifted off the ground
- D.The pawls are seated on a bed-section rung✓ Answer
If the pawls are not fully seated over a bed-section rung, the fly can drop under a climber's weight, so firefighters confirm the locks before climbing. The halyard stays in its pulley and is secured, the butt spurs must stay in contact with the ground to resist slipping, and an unlocked fly is exactly the failure the check is meant to catch.
Ref QB-PM9W2RSource: NFPA 1010 (2024), Fire Fighter I — ground ladders; confirm pawls locked before climbingReport a problem with this question
13. Besides the routine annual test, which event requires a ground ladder to be service tested before it goes back into service?
- A.It was exposed to direct flame at a fire✓ Answer
- B.It passed its routine monthly inspection
- C.It was washed with mild soap and water
- D.It was moved to a different apparatus
Direct flame or high heat can weaken ladder materials without obvious signs, so heat exposure is one of the events (with overloading, damage and repairs) that triggers a service test before reuse. Washing with mild soap and water is normal care, moving a ladder between apparatus does not stress it, and passing a visual inspection does not prove strength.
Ref QB-75F3NRSource: NFPA 1932 (now NFPA 1930) — service-test triggers: heat exposure, overload, damage, repairReport a problem with this question
14. Why do ladder-maintenance guidelines prohibit painting wood ground ladders, other than small identification marks at the ends?
- A.Paint makes dry wood conduct electricity
- B.Paint can hide cracks, rot and other defects✓ Answer
- C.Paint adds too much weight for the duty rating
- D.Paint blocks the heat-sensor label readings
An opaque coat of paint covers the wood surface, so cracks, splits, soft spots, darkening and water rot that an inspector needs to see can go unnoticed. Wood ladders are protected with a clear finish such as varnish instead, which keeps the grain visible; paint does not turn dry wood conductive or add meaningful weight.
Ref QB-SMBWJUSource: NFPA 1932 (now NFPA 1930) — ground-ladder maintenance; do not paint wood ladders except identification marksReport a problem with this question
15. A firefighter grabs a pike pole and a drywall hook to pull down a section of ceiling. These tools belong to which forcible entry tool category?
- A.Cutting tools
- B.Pushing/pulling tools✓ Answer
- C.Prying tools
- D.Striking tools
Pike poles, plaster hooks, drywall hooks and closet hooks are pushing/pulling tools: they extend a firefighter's reach to push through or pull down ceilings and walls. Prying tools such as the Halligan create leverage, striking tools such as the flat-head axe and sledge deliver impact, and cutting tools such as saws and bolt cutters sever material.
Ref QB-A5H36VSource: NFPA 1010 (2024), Fire Fighter I — forcible entry; four basic tool categoriesReport a problem with this question
16. A firefighter needs to drive the fork of a Halligan bar between a door and its jamb. Which tool is the appropriate one to strike the Halligan?
- A.A pick-head axe
- B.A flat-head axe✓ Answer
- C.A pike pole butt
- D.A bolt cutter
The flat-head axe has a broad striking face and is paired with the Halligan as the irons for exactly this job. A pick-head axe should never be used as a striking tool, because a glancing or missed blow can swing the exposed pick into the firefighter holding the bar; pike poles and bolt cutters are not built to take hammer blows.
Ref QB-RMYJDTSource: NFPA 1010 (2024), Fire Fighter I — forcible entry tool safety; flat-head axe as striking tool, never a pick-head axeReport a problem with this question
17. The wooden handle on a station axe has become rough and weathered. What is the proper maintenance?
- A.Soak it in water so the wood swells tight
- B.Sand it and coat it with high-gloss paint
- C.Sand it smooth and apply boiled linseed oil✓ Answer
- D.Wrap the whole handle in electrical tape
Wood handles are sanded to remove splinters and rough spots and then treated with boiled linseed oil, which penetrates and protects the wood while leaving cracks and damage visible. Paint and tape both hide defects in the handle, and soaking the wood leads to swelling, shrinking and loosening of the head as it dries.
Ref QB-956RYTSource: NFPA 1010 (2024), Fire Fighter I — forcible entry tool maintenance; wood handles sanded and oiled, not paintedReport a problem with this question
18. A crew must cut through a steel security gate with a rotary saw. Which blade is the appropriate choice?
- A.A masonry-cutting abrasive disc
- B.A carbide-tipped wood blade
- C.A steel-tooth wood-cutting blade
- D.A metal-cutting abrasive disc✓ Answer
Abrasive discs are made for specific materials, and a metal-cutting disc is the one designed for steel. Carbide-tipped and toothed wood blades are meant for wood and light materials; on steel their teeth can break off and be thrown, and a masonry disc is formulated for concrete and stone rather than metal.
Ref QB-KM7WHMSource: NFPA 1010 (2024), Fire Fighter I — forcible entry tools; rotary saw blade selection by materialReport a problem with this question
19. After trying the knob and confirming that a wooden, inward-swinging door is locked (no hinges are visible from outside), how should the firefighter force it?
- A.Drive the Halligan fork in at the jamb and push the door in✓ Answer
- B.Knock the knob off with a pick-head axe and reach inside
- C.Set the Halligan adze at the lock and pry the door outward
- D.Pull the hinge pins on the outside and lift the door away
An inward-swinging door opens away from the firefighter, so the Halligan's fork is driven between the door and jamb near the lock and the door is forced inward in the direction it already swings. Hinge pins are not accessible because the hinges are inside, prying outward fights the door stop, and striking with a pick-head axe is an impalement hazard.
Ref QB-45D35NSource: NFPA 1010 (2024), Fire Fighter I — forcible entry; forcing inward-swinging doors (try before you pry)Report a problem with this question
20. In through-the-lock forcible entry, the K-tool is used together with a Halligan for leverage. What is the K-tool's primary job?
- A.Spread the door away from the jamb beside the lock
- B.Cut through a padlock shackle with its leverage jaws
- C.Pull the lock cylinder so the lock can be worked✓ Answer
- D.Shear the deadbolt by striking hard on the lock face
The K-tool's blades bite into the lock cylinder, and the Halligan levers it out; with the cylinder removed, a key tool is used to move the mechanism and open the lock with little damage to the door. It is not a cutter, spreader or striking tool, which is why through-the-lock entry is chosen when preserving the door matters.
Ref QB-MJM3QNSource: NFPA 1010 (2024), Fire Fighter I — forcible entry; through-the-lock technique (K-tool and key tool)Report a problem with this question
21. During forcible entry, the glass in one door breaks into many small, cube-like pieces when struck. A second door's glass cracks into a web but stays in one sheet. What types of glass are these?
- A.First tempered, second laminated✓ Answer
- B.First laminated, second tempered
- C.First plate, second polycarbonate
- D.First polycarbonate, second plate
Tempered glass is heat-treated so that it fails all at once into small, relatively blunt cubes. Laminated glass has a plastic layer between sheets that holds the pieces together, so it cracks but stays in place and must be cut rather than cleared by breaking. Plate (annealed) glass breaks into long, sharp shards, and polycarbonate resists breaking and is cut with a saw.
Ref QB-43FW4NSource: NFPA 1010 (2024), Fire Fighter I — forcible entry; glass types (tempered vs. laminated)Report a problem with this question
22. Firefighters have forced a commercial roll-up door and raised it partway. Before crews pass underneath, what should be done to keep it from dropping on them?
- A.Cut the lift cables so the door hangs freely
- B.Kick a wooden door chock under one bottom corner
- C.Clamp locking pliers onto the track below the door✓ Answer
- D.Prop the bottom edge with one pike pole at center
Locking pliers clamped onto the door track just below the bottom edge physically block the door from rolling down, even if springs, cables or the operator fail. Cutting the lift cables removes support and can let the door fall, and a single pike pole or a chock under one corner can slip or be knocked out as crews and hose move through.
Ref QB-KJ9RHMSource: NFPA 1010 (2024), Fire Fighter I — forcible entry; securing overhead and roll-up doors with locking pliers on the trackReport a problem with this question
Other topics in this exam
Original practice questions written to the job performance requirements of NFPA 1010 (2024), which replaced NFPA 1001 for Fire Fighter I and II, and NFPA 470 for hazardous materials Awareness and Operations. Not affiliated with or endorsed by NFPA, IFSAC, the Pro Board, or any state fire academy. Each state writes its own certification exam — check your state's fire academy or certification office for its format and which edition it tests. NFPA 1010 standard →