Quibank app: now on the App Store — free, works offline. Get the app ↗

22 Fire Control, Overhaul, Ropes & Knots Practice Questions & Answers

Every Fire Control, Overhaul, Ropes & Knots practice question from the Firefighter I & II Certification Practice Test, with the correct answer and a short explanation.

Start practice test →
  1. 1. During a training evolution, a life safety rope catches a firefighter in a short fall, sharply shock-loading it. What should happen to that rope?

    • A.Keep it until its next annual inspection
    • B.Remove it from life safety service✓ Answer
    • C.Return it to service after washing it
    • D.Keep it in service if it looks undamaged

    An impact or shock load can damage the load-bearing fibers inside the rope without leaving visible marks, so a shock-loaded life safety rope is taken out of life safety service (downgraded or destroyed). Washing does not restore strength, a normal-looking sheath does not prove the core is intact, and waiting for a scheduled inspection leaves a compromised rope in use.

    Ref QB-NFHX8BSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — rope care and reasons for removal from service; NFPA 2500 (formerly NFPA 1983) — life safety ropeReport a problem with this question

  2. 2. Which of these tasks requires a life safety rope rather than a utility rope?

    • A.Cordoning off an unsafe collapse area
    • B.Hoisting an axe up to the roof crew
    • C.Lowering a firefighter from a window✓ Answer
    • D.Securing a ladder to a porch railing

    Life safety rope is any rope that supports a person's weight during rescue, firefighting, or training, so lowering a firefighter calls for it. Hoisting tools, cordoning off an area, and securing equipment are utility tasks; utility rope has no NFPA performance standard and is never used to support a person.

    Ref QB-4YYEG9Source: NFPA 1010 (2024) Ch. 6, Fire Fighter I — life safety rope vs utility ropeReport a problem with this question

  3. 3. In a kernmantle life safety rope, which part provides most of the rope's strength?

    • A.The braided outer sheath
    • B.The core inside the sheath✓ Answer
    • C.The sheath and core equally
    • D.The twisted outer strands

    Kernmantle rope has a braided sheath (mantle) over a load-bearing core (kern); the core carries roughly 75 percent of the strength while the sheath mainly protects it from abrasion and dirt. Twisted strands describe laid rope, a different construction mostly used as utility rope.

    Ref QB-MF6M3ASource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — rope construction (kernmantle core and sheath)Report a problem with this question

  4. 4. A firefighter must join two ropes of noticeably different diameters. Which knot is designed for this job?

    • A.A bowline knot
    • B.A water knot
    • C.A becket bend✓ Answer
    • D.A clove hitch

    The becket (sheet) bend joins ropes of unequal diameter, and also rope to webbing or chain, because its bight-and-wrap shape grips the smaller line against the larger one. The water knot joins webbing, the clove hitch attaches rope to an object, and the bowline forms a fixed loop.

    Ref QB-7Y2FZCSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — knot types and usesReport a problem with this question

  5. 5. When hoisting an axe or pike pole, a clove hitch is tied on the handle and half hitches are added along it. What do the half hitches do?

    • A.Keep the tool aligned with the rope✓ Answer
    • B.Replace the need for a tag line
    • C.Shorten the rope for a faster lift
    • D.Let the knot release under load

    A half hitch is always used with another knot to keep a long object aligned during a hoist, so the axe or pike pole rides parallel to the rope instead of swinging crosswise and snagging. A tag line is still required to control the load and keep it off the building, and the hitches are meant to hold, not release.

    Ref QB-QF8MKDSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — hoisting tools and equipment using appropriate knotsReport a problem with this question

  6. 6. A crew is hoisting a charged attack line to an upper floor. How should the nozzle be handled?

    • A.Removed and hoisted up in a separate bag
    • B.Left partly open to bleed air from the line
    • C.Shut off and secured in the closed position✓ Answer
    • D.Set to a wide fog pattern before hoisting

    A charged line is hoisted with the nozzle shut off and tied or secured closed, often by running the rope through the bail, because an accidental opening would turn the line into a whipping, uncontrolled stream above the crew. Bleeding air or setting a pattern is done after the line is in position.

    Ref QB-6YP4UBSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — hoisting charged and uncharged hoselinesReport a problem with this question

  7. 7. What is the primary goal of property conservation (loss control) at a structure fire?

    • A.Limit further damage to the building and contents✓ Answer
    • B.Remove all contents before the fire attack begins
    • C.Recover valuables for the owner's insurance adjuster
    • D.Determine the fire's cause for the incident report

    Property conservation protects the structure and its contents from further damage by smoke, water, and weather, which reduces the loss and builds public goodwill. Determining cause is the investigator's job, and moving everything out before attack wastes staffing; salvage begins as early as staffing allows, often alongside the attack.

    Ref QB-PFV9ECSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — conserve property (loss control)Report a problem with this question

  8. 8. Water from hose streams on the floor above is pouring steadily into a room. The officer wants it carried out of the building, not just held. What should the crew build?

    • A.A balloon throw over the furniture
    • B.A dike of rolled covers at the door
    • C.A water chute leading out a window✓ Answer
    • D.A catchall under the heaviest leak

    A water chute is a cover formed into a trough that channels water out a window or door, so it moves water out of the building. A catchall only contains water for later removal, a balloon throw is a way to spread a cover over contents, and a dike at the door holds water in place rather than removing it.

    Ref QB-9YR4CFSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — loss control: water chutes and catchallsReport a problem with this question

  9. 9. Before covering a room's furniture with salvage covers, where should the crew group the items?

    • A.In the room's center, raised off the floor✓ Answer
    • B.Beneath the windows, close to the exit
    • C.Against the outer walls, flush to the floor
    • D.Out in the hallway, stacked by the door

    Clustering contents in the center of the room keeps them away from walls, where water runs down from above, and lets one or two covers protect everything; raising items off the floor keeps them out of pooled water. Moving contents to windows or hallways spreads them out and blocks the crew's routes.

    Ref QB-SFX9XFSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — conserve property: grouping and covering contentsReport a problem with this question

  10. 10. The fire is knocked down and the smoke has lifted, so overhaul is starting. When may the crew remove their SCBA?

    • A.After fans have run for about ten minutes
    • B.Once the fire is declared under control
    • C.Once all visible smoke has fully cleared
    • D.When air monitoring shows the area is safe✓ Answer

    Overhaul atmospheres stay loaded with carbon monoxide, hydrogen cyanide, and fine particulates even after visible smoke clears, so SCBA stays on until air monitoring confirms the area is safe. Clear-looking air, a control declaration, or a set fan run time does not measure the toxic gases that remain.

    Ref QB-9XC8JPSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — overhaul hazards and respiratory protectionReport a problem with this question

  11. 11. During overhaul, a firefighter finds two separate burn areas joined by a pour pattern on the floor. What should the firefighter do?

    • A.Leave it undisturbed and notify the officer✓ Answer
    • B.Shovel the debris outside to prevent rekindle
    • C.Bag the suspect items for the investigator
    • D.Flood the area to cool it before moving on

    Multiple separate points of origin and pour patterns are possible signs of arson, so the area is left in place and reported up the chain so investigators can document it. Shoveling, flooding, or collecting the items yourself destroys the context investigators need and can break the chain of custody.

    Ref QB-RE73YNSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — overhaul: preserving evidence of fire causeReport a problem with this question

  12. 12. During overhaul, a crew opens a wall and finds a smoldering stud bay. Which water application best fits overhaul goals?

    • A.A wide fog at full flow across the room
    • B.A low-flow handline aimed into the void✓ Answer
    • C.No water, just a fire watch on the wall
    • D.A full-flow solid stream into the void

    Overhaul aims to extinguish all hidden fire while limiting water damage, so a small handline at low flow is applied directly into the opened void. A full-flow solid stream or room-wide fog adds needless water damage, and leaving a smoldering void unextinguished invites a rekindle.

    Ref QB-AXQJQQSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — overhaul: locating and extinguishing hidden fireReport a problem with this question

  13. 13. In which situation is an indirect attack (directing the stream into the overhead to make steam) inappropriate?

    • A.When victims or crews are inside the space✓ Answer
    • B.When the room is fully involved and empty
    • C.When steam conversion is the main objective
    • D.When the fire is in a closed, unvented room

    An indirect attack relies on large-scale steam production in a closed compartment, which drives heat and steam onto anyone inside and can cause serious burns, so it is used only when no victims or crews are present. A fully involved, unoccupied, closed room where steam conversion is the goal is exactly where the method fits.

    Ref QB-SEJD5QSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — interior attack: direct, indirect and combination methodsReport a problem with this question

  14. 14. Which nozzle practice prevents water hammer on an attack line?

    • A.Open and close the nozzle gradually✓ Answer
    • B.Close the nozzle fast after knockdown
    • C.Kink the hose before closing the nozzle
    • D.Keep the bail half open at all times

    Water hammer is a pressure surge created when moving water is stopped suddenly; opening and closing the nozzle slowly lets the water column change speed gradually, protecting the hose, pump, and fittings. Snapping the nozzle shut is the classic cause, and a half-open bail or a kink does not address the sudden flow change.

    Ref QB-BX3WVRSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — interior attack: nozzle operation and water hammerReport a problem with this question

  15. 15. Fire is burning in a basement. The only interior stairs lead down from the first floor, and an outside basement door is available. Unless directed otherwise, what is the preferred attack approach?

    • A.Hold the line at the top of the interior stairs
    • B.Advance down the interior stairs right away
    • C.Wait outside until the fire vents itself
    • D.Attack from the outside basement entrance✓ Answer

    An interior stairway over a basement fire acts as a chimney for heat and smoke, so crews descending it move through the heat column; an exterior or other grade-level entry lets the line reach the fire without that exposure. Holding at the top of the stairs leaves the fire unchecked, and waiting for it to vent lets it spread upward.

    Ref QB-TEWQARSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — interior attack: below-grade firesReport a problem with this question

  16. 16. An engine crew is approaching a burning passenger car parked on a slight grade. Which approach is best?

    • A.Straight in from the rear, upwind and uphill
    • B.At a 45° angle from the side, downhill and downwind
    • C.Head-on toward the front bumper, from upwind
    • D.At a 45° angle from the side, upwind and uphill✓ Answer

    A 45-degree side approach keeps crews out of the line of bumpers, gas struts, and hood or hatch lift cylinders, which can launch when heated, while staying upwind and uphill keeps them out of smoke and away from fuel that runs downhill. Approaching head-on or from the rear puts crews directly in that launch path.

    Ref QB-CXE83TSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — attacking passenger vehicle firesReport a problem with this question

  17. 17. A crew is working a fire involving an electric vehicle's lithium-ion battery pack. Which statement is accurate?

    • A.Once knocked down, the battery will not reignite
    • B.Water must never be applied to the battery pack
    • C.It needs large volumes of water for a long time✓ Answer
    • D.A short burst of water will cool it for good

    Lithium-ion cells can go into thermal runaway, generating their own heat from cell to cell, so suppression takes large volumes of water applied over an extended time to cool the pack. Short bursts do not stop the chain reaction, water is the recognized cooling agent rather than a hazard, and these batteries can reignite hours after apparent knockdown.

    Ref QB-UE93GSSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — passenger vehicle fires: alternative fuels and high-voltage batteriesReport a problem with this question

  18. 18. At a car fire, burning metal wheel components flare brightly each time a small fog stream hits them. What is the best action?

    • A.Hit it with brief, repeated bursts of water
    • B.Use large volumes of water or a Class D agent✓ Answer
    • C.Apply a light mist so the metal cools slowly
    • D.Stop all water and let the metal burn itself out

    Burning magnesium and similar combustible metals react with small amounts of water, which is why they flare; a large volume of water cools the metal faster than the reaction can feed, or a Class D agent smothers it. Light mist and short bursts keep feeding the reaction, and walking away leaves the rest of the vehicle burning.

    Ref QB-5XXVUHSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — passenger vehicle fires: combustible metal componentsReport a problem with this question

  19. 19. On a wind-driven grass fire, which part of the fire is spreading fastest?

    • A.The flanks
    • B.The head✓ Answer
    • C.The heel
    • D.The fingers

    The head is the leading edge driven by wind or slope and is the fastest-moving, most intense part of a ground cover fire. The heel (rear) burns slowly back into the wind, the flanks are the sides running roughly parallel to the spread, and fingers are narrow strips extending out from the main fire.

    Ref QB-MESQ9HSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — ground cover fires: parts of a wildland fireReport a problem with this question

  20. 20. A crew is starting a direct attack on a grass fire with handlines. Where should the attack begin?

    • A.Downhill of the fire, directly below the head
    • B.From an anchor point, working along the flanks✓ Answer
    • C.At an island of unburned fuel in the black
    • D.At the head, meeting the fire straight on

    Starting from an anchor point, a secure barrier such as a road or the burned area, keeps the fire from outflanking the crew, and working the flanks toward the head narrows the fire safely. Meeting the head straight on or positioning downhill below it puts the crew in the path of the fastest, most intense spread, and an island inside the black is not a secure starting point.

    Ref QB-YQCRYBSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — ground cover fires: anchor point and flank attackReport a problem with this question

  21. 21. A propane cylinder has gas burning at its valve, and flame is impinging on the tank. What is the correct approach for the hose team?

    • A.Knock down the flame first, then close the valve
    • B.Blow out the flame with a straight stream right away
    • C.Lay the tank on its side to reduce the flame size
    • D.Cool the tank and let it burn until the valve is shut✓ Answer

    Cooling with fog streams protects the container from heat-induced failure, while the flame itself is left burning because it is consuming the gas; closing the valve is what extinguishes the fire. Putting the flame out while gas still flows lets an unburned vapor cloud build up that can find an ignition source and explode, and laying a cylinder down can release liquid propane.

    Ref QB-G8JWJCSource: NFPA 1010 (2024) Ch. 7, Fire Fighter II — controlling a flammable gas cylinder fireReport a problem with this question

  22. 22. To shut off natural gas at a building's outside meter, a firefighter turns the quarter-turn valve. In which position is the valve closed?

    • A.With the tang in line with the pipe
    • B.After a full turn of the valve tang
    • C.With the tang pointing at the meter
    • D.With the tang crosswise to the pipe✓ Answer

    Quarter-turn gas meter valves are open when the tang (the flat tab) runs in line with the pipe and closed when it is turned 90 degrees to sit crosswise, which blocks the flow path. A full turn simply returns the valve to where it started, and the tang is never meant to point at the meter. Once shut off, gas service is restored by the utility, not the fire department.

    Ref QB-ZQQ36DSource: NFPA 1010 (2024) Ch. 6, Fire Fighter I — controlling building utilities (natural gas)Report a problem with this question

Other topics in this exam

Original practice questions written to the job performance requirements of NFPA 1010 (2024), which replaced NFPA 1001 for Fire Fighter I and II, and NFPA 470 for hazardous materials Awareness and Operations. Not affiliated with or endorsed by NFPA, IFSAC, the Pro Board, or any state fire academy. Each state writes its own certification exam — check your state's fire academy or certification office for its format and which edition it tests. NFPA 1010 standard →