24 Firefighter II Operations Practice Questions & Answers
Every Firefighter II Operations practice question from the Firefighter I & II Certification Practice Test, with the correct answer and a short explanation.
Start practice test →1. A Fire Fighter II arrived first, established command, and has run the incident for 10 minutes when a battalion chief arrives to take over. How should command be transferred?
- A.Face-to-face, with a briefing on current conditions✓ Answer
- B.Automatically, the moment a higher rank arrives
- C.By radio, announcing only the new commander's name
- D.In writing, on a note left at the command post
Under ICS, command transfers only by a deliberate handoff, and face-to-face is preferred because the incoming commander must receive a status briefing on conditions, assignments, resources and hazards. The arrival of a higher rank does not transfer command by itself, and a name-only radio message or a note leaves the new commander without the information needed to run the incident. The transfer is then announced to everyone on the incident.
Ref QB-YNKAARSource: NIMS/ICS (FEMA) — transfer of command; NFPA 1010 (2024) Ch. 7, Fire Fighter II (formerly NFPA 1001 Ch. 5) — assuming and transferring commandReport a problem with this question
2. Under ICS, which of these positions belongs to the Command Staff rather than the General Staff?
- A.Logistics Section Chief
- B.Planning Section Chief
- C.Operations Section Chief
- D.Incident Safety Officer✓ Answer
The Command Staff reports directly to the Incident Commander and consists of the Safety Officer, the Public Information Officer and the Liaison Officer. The General Staff is made up of the section chiefs for Operations, Planning, Logistics and Finance/Administration, so the three section-chief options are all General Staff positions.
Ref QB-G6SFVRSource: NIMS (FEMA) — ICS Command Staff and General StaffReport a problem with this question
3. An interior division supervisor now has nine crews reporting directly, which ICS considers too wide a span of control. How many direct reports does ICS treat as the optimum?
- A.Three
- B.Ten
- C.Five✓ Answer
- D.Seven
ICS recommends a span of control of 3 to 7 resources per supervisor, with 5 as the optimum, so a supervisor can track and direct every unit safely. Seven is the upper limit of the range rather than the ideal, three is the lower limit, and ten exceeds the range; the fix for nine crews is to split them into additional divisions or groups.
Ref QB-ZNXMFSSource: NIMS (FEMA) — ICS span of control (3 to 7, optimum 5)Report a problem with this question
4. Crews assigned to one function, such as ventilation, wherever it is needed across the whole incident are organized under ICS as a:
- A.Ventilation Group✓ Answer
- B.Ventilation Branch
- C.Ventilation Task Force
- D.Ventilation Division
ICS organizes resources by geography into divisions (such as a floor or side of a building) and by function into groups, so a crew doing ventilation anywhere on the incident is a group. A branch is a higher level used when the number of divisions and groups exceeds span of control, and a task force is a temporary mix of different resource types under one leader.
Ref QB-D6QFCNSource: NIMS (FEMA) — ICS divisions (geographic) and groups (functional)Report a problem with this question
5. Fire Fighter II crews choose attack assignments according to the three overall incident priorities. In what order do those priorities rank?
- A.Incident stabilization, life safety, property conservation
- B.Property conservation, life safety, incident stabilization
- C.Life safety, incident stabilization, property conservation✓ Answer
- D.Life safety, property conservation, incident stabilization
Protecting the lives of occupants and responders always comes first, then stabilizing the incident so it stops growing, and only then conserving property. Stabilization ranks above property because controlling the fire is what ultimately protects property; spending effort on salvage while the fire is still spreading reverses that logic.
Ref QB-WNVMXNSource: NFPA 1010 (2024) Ch. 7, Fire Fighter II (formerly NFPA 1001 Ch. 5) — incident priorities and coordinated fire attackReport a problem with this question
6. A foam concentrate is labeled 3%. What does that percentage describe?
- A.3 parts water mixed with 97 parts of concentrate
- B.3 parts concentrate mixed with 97 parts of water✓ Answer
- C.3 parts concentrate in 100 parts of finished foam
- D.Finished foam expands to 3 times the solution volume
The percentage is the share of concentrate in the foam solution, which is concentrate plus water, so 3% means 3 parts concentrate to 97 parts water. Finished foam is that solution after air has been added by agitation, so the percentage is not measured against finished foam, and how much the foam grows is a separate value called the expansion ratio.
Ref QB-E63THPSource: NFPA 11 — low-, medium- and high-expansion foam (foam concentrate, solution and proportioning)Report a problem with this question
7. A tanker carrying ethanol has overturned, and the spilled fuel is burning. Which foam concentrate is needed?
- A.Standard 3% AFFF concentrate
- B.Regular protein foam concentrate
- C.Alcohol-resistant AFFF concentrate✓ Answer
- D.Class A foam concentrate
Ethanol is a polar solvent that mixes with water, so it pulls the water out of ordinary foam and destroys the blanket. Alcohol-resistant concentrates form a polymer membrane between the fuel and the foam, which keeps the blanket intact. Standard AFFF, protein foam and Class A foam are designed for hydrocarbons or ordinary combustibles and break down on polar solvents.
Ref QB-XN8Y4QSource: NFPA 11 — alcohol-resistant foam concentrates for polar solvent (water-miscible) fuelsReport a problem with this question
8. Burning diesel fuel has pooled against the base of a concrete wall. Which foam application method is preferred?
- A.Rain-down, lofting the stream so foam falls onto the fuel
- B.Bank-down, deflecting foam off the wall onto the fuel✓ Answer
- C.Direct plunge, aiming the stream right into the burning fuel
- D.Roll-on, bouncing foam onto the ground ahead of the spill
When a wall or other object is next to the fuel, bank-down lets foam strike the object, lose energy and flow gently across the surface, building a blanket without disturbing the fuel. Roll-on suits open ground spills with no object to deflect off, and rain-down is the least preferred overhead method. Plunging foam into the fuel agitates and splashes it, spreading the fire and breaking the blanket.
Ref QB-B6ZSZJSource: NFPA 1010 (2024) Ch. 7, Fire Fighter II (formerly NFPA 1001 Ch. 5) — Class B foam application methodsReport a problem with this question
9. A crew connects an in-line eductor rated at 95 gpm to a nozzle that flows 125 gpm, and the line produces little or no foam. What is the most likely cause?
- A.The concentrate setting is too low for the nozzle
- B.The eductor works only with a fog nozzle setting
- C.The attack line beyond the eductor is too short
- D.The nozzle flow does not match the eductor rating✓ Answer
An in-line eductor uses the venturi effect, and it picks up concentrate correctly only when the water flowing through it matches its rated flow, so the nozzle gpm must match the eductor gpm. A mismatched nozzle upsets the pressure drop across the venturi and pickup fails. A short hose lay is not the problem, because too much hose after the eductor is what creates back-pressure, and the concentrate percentage setting does not fix a flow mismatch.
Ref QB-UN6YKKSource: NFPA 11 — foam proportioning; NFPA 1010 (2024) Ch. 7 (formerly NFPA 1001 Ch. 5) — in-line eductor operationReport a problem with this question
10. Flame is impinging on a horizontal LPG tank. Where should cooling streams be concentrated to reduce the risk of a BLEVE?
- A.Into the relief valve opening on the top
- B.On the ground beneath the tank's supports
- C.On the lower shell, below the liquid level
- D.On the upper shell, above the liquid level✓ Answer
Below the liquid level, the boiling liquid absorbs heat and protects the steel, but the metal around the vapor space has nothing to carry heat away, so it weakens and can fail and cause a BLEVE. Cooling streams therefore go on the upper shell, especially where flame impinges. Spraying into the relief valve can interfere with its operation, and wetting the ground does not cool the shell.
Ref QB-SMBDWESource: NFPA 1010 (2024) Ch. 7, Fire Fighter II (formerly NFPA 1001 Ch. 5) — flammable gas container fires and BLEVE preventionReport a problem with this question
11. From outside, a firefighter aims a thermal imaging camera through a closed window to check for heat inside a room. Why is this reading unreliable?
- A.The camera detects only flame, not hot surfaces
- B.Glass blocks infrared, so the camera shows the pane✓ Answer
- C.Glass amplifies infrared, so the room reads too hot
- D.The camera needs smoke in the air to display heat
A thermal imaging camera reads infrared energy given off by surfaces, and ordinary glass does not let that long-wave infrared through; it also reflects heat from other objects. The image therefore shows the temperature of the window pane and reflections, not conditions in the room. The camera works in clear air as well as smoke and does detect hot surfaces, not just flame.
Ref QB-9568BESource: NFPA 1010 (2024) Ch. 7 (formerly NFPA 1001 Ch. 5) — thermal imaging limitations (glass and water surfaces block or reflect infrared)Report a problem with this question
12. A records archive is protected by a sprinkler system whose pipes hold air. Water enters the piping only after a separate detection system operates, and it discharges only where a head has fused. What type of system is this?
- A.Dry-pipe system
- B.Pre-action system✓ Answer
- C.Wet-pipe system
- D.Deluge system
A pre-action system needs a detection system to open its valve and fill the pipes, and closed heads still have to fuse before water flows, which protects water-sensitive contents from accidental discharge. A dry-pipe system releases water when a fused head lets the air pressure drop, with no separate detection. A deluge system has open heads that all flow at once, and a wet-pipe system holds water in the pipes at all times.
Ref QB-RMY2RDSource: NFPA 13 — preaction, dry-pipe, deluge and wet-pipe sprinkler systemsReport a problem with this question
13. While checking a sprinkler riser, you find an outside stem and yoke valve. Which observation indicates the valve is open?
- A.The handwheel spins freely in either direction
- B.The target window on the post reads SHUT
- C.The threaded stem extends past the handwheel✓ Answer
- D.The stem sits flush, hidden inside the yoke
On an outside stem and yoke valve the threaded stem rises out through the handwheel as the valve opens, so a visible, extended stem means open and a flush stem means closed. A target window reading OPEN or SHUT belongs to a post indicator valve, not this valve, and a handwheel that spins freely points to damage rather than position. A sprinkler control valve should not be closed without the incident commander's approval.
Ref QB-85TV5DSource: NFPA 13 / NFPA 25 — sprinkler control valves (OS&Y and post indicator valves)Report a problem with this question
14. In a high-rise, the stairwell standpipe is a Class I system. What does that class provide?
- A.1½-inch hose stations for occupant use
- B.2½-inch outlets for fire department use✓ Answer
- C.Automatic sprinkler feed with no outlets
- D.Both 1½-inch hose and 2½-inch outlets
NFPA 14 defines Class I standpipes as having 2½-inch hose connections for fire departments and others trained in handling heavy fire streams. Class II provides 1½-inch hose stations mainly for trained occupants, and Class III combines both. A standpipe's purpose is to supply hose outlets, so a riser with no outlets is not a standpipe class.
Ref QB-QMMQJCSource: NFPA 14 — standpipe system classes (Class I, II, III)Report a problem with this question
15. During overhaul in the room where the fire appears to have started, you find a melted plastic container that smells strongly of gasoline. What should you do?
- A.Leave it in place, protect it, and notify your officer✓ Answer
- B.Shovel it out with the other debris to finish overhaul
- C.Cool it with a hose stream, then move it to the yard
- D.Bag it immediately and carry it out to the apparatus
A firefighter's job is to recognize and protect possible evidence, while the investigator documents, collects and interprets it. Leaving the item where it lies preserves its location relative to fire patterns, and a documented chain of custody depends on the investigator collecting it. Bagging it yourself, washing it with a hose stream or shoveling it out can destroy residue and its value as evidence.
Ref QB-75FJYBSource: NFPA 921 — evidence preservation; NFPA 1010 (2024) Ch. 7, Fire Fighter II (formerly NFPA 1001 Ch. 5) — protecting evidence of fire cause and originReport a problem with this question
16. Which observation at a house fire most strongly suggests the fire may be incendiary?
- A.A V-pattern on the wall directly above the stove
- B.Heavy charring around the main electrical panel
- C.Separate, unconnected fires in several rooms✓ Answer
- D.Thick black smoke coming from a burning sofa
Multiple separate points of origin with no fire spread connecting them are a classic incendiary indicator, because accidental fires normally start in one place. Charring near an electrical panel or a V-pattern above a stove points to a possible accidental source, and black smoke from upholstered furniture is normal for plastics and foam. The firefighter reports the indicator; the investigator decides the cause.
Ref QB-PM9DDBSource: NFPA 921 — incendiary fire indicators (multiple fires)Report a problem with this question
17. At a crash, the passenger-side frontal airbag has not deployed. Under the commonly taught 5-10-20 rule, how far should rescuers keep their bodies and tools from it?
- A.10 inches
- B.5 inches
- C.15 inches
- D.20 inches✓ Answer
The 5-10-20 rule sets the minimum clearance from undeployed airbags at 5 inches for side airbags, 10 inches for the driver's frontal airbag and 20 inches for the passenger's frontal airbag. The passenger bag is the largest and deploys the farthest, so it needs the greatest clearance; using the driver or side distance would leave a rescuer inside its deployment zone.
Ref QB-6548TASource: NFPA 1010 (2024) Ch. 7, Fire Fighter II (formerly NFPA 1001 Ch. 5) — vehicle extrication; undeployed airbag 5-10-20 clearance ruleReport a problem with this question
18. Under NFIRS, the national fire incident reporting system departments used until NERIS replaced it in January 2026, which module had to be completed for every incident, whatever its type?
- A.Structure Fire Module
- B.Arson Module
- C.Fire Module
- D.Basic Module✓ Answer
In NFIRS the Basic Module records the core facts of every incident, such as incident type, location, property use and actions taken, so it is required for all incidents, including medical calls and false alarms. The Fire, Structure Fire, Arson and casualty modules are added only when the incident type calls for them. Because the report is a legal record, its narrative must be accurate, objective and timely. Since January 1, 2026 incidents are reported in NERIS, but state exams built on IFSTA material may still ask about NFIRS.
Ref QB-WMRQKKSource: USFA NFIRS 5.0 — Basic Module required for all incidents; USFA NFIRS sunset (NERIS-only submission from Jan 1, 2026); NFPA 1010 (2024) Ch. 7 (formerly NFPA 1001 Ch. 5) — completing a basic incident reportReport a problem with this question
19. During a home fire safety survey requested by a resident, you find smoke alarms that pass the test-button check but are 12 years old. What should you advise?
- A.Replace them, since units are due every 10 years✓ Answer
- B.Keep them, since a passing test means they still work
- C.Replace only the batteries, then retest each month
- D.Keep them until they begin to chirp or fail a test
Smoke alarm sensors lose sensitivity with age, so NFPA 72 requires replacing smoke alarms no more than 10 years after the date of manufacture. The test button mainly confirms the horn and circuit, not that the sensor still detects smoke reliably, so a passing test does not make an old unit safe. New batteries do not renew an aging sensor.
Ref QB-D5KJZJSource: NFPA 72 — smoke alarm replacement (no more than 10 years from date of manufacture); NFPA 1010 (2024) Ch. 7 (formerly NFPA 1001 Ch. 5) — residential fire safety surveyReport a problem with this question
20. Your crew is preparing for the annual hose service test under NFPA requirements. Which practice is correct?
- A.Limit each test line to 300 ft and mark the couplings✓ Answer
- B.Hold test pressure for only 30 seconds before passing
- C.Test at the pump's maximum pressure, not the marking
- D.Connect lengths into test lines up to 500 ft long
NFPA hose-testing requirements (formerly NFPA 1962, now part of NFPA 1930) limit each test layout to 300 ft so problems are easier to find and a burst releases less energy, and couplings are marked so any slippage during the test can be seen. The hose is tested at the service test pressure for its marking, not at whatever the pump can produce, and that pressure is held for at least 3 minutes while the hose is checked for leaks, coupling slippage and jacket damage.
Ref QB-VPBJEJSource: NFPA 1962 (now part of NFPA 1930) — service testing of fire hose (test length limit, coupling marking, test duration)Report a problem with this question
21. A propane cylinder outside a shed has a burning leak at its valve, and the valve is jammed open so it cannot be closed. What should the hoseline crew do about the flame?
- A.Let it burn while cooling the cylinder with water✓ Answer
- B.Put it out with dry chemical, then cool the tank
- C.Put it out with a straight stream, then retreat
- D.Smother it with foam, then plug the valve opening
NFPA 1010 requires that the flame not be extinguished unless the leaking gas is eliminated. If the fire is put out while gas keeps escaping, the unburned gas spreads, finds an ignition source and can re-ignite explosively. Since the valve cannot be closed, the crew lets the gas burn in a controlled way and cools the cylinder to keep pressure down, advancing from an identified safe haven and facing the cylinder on approach and retreat.
Ref QB-D7HQZJSource: NFPA 1010 (2024) 7.3.4, Fire Fighter II (formerly NFPA 1001-2019 5.3.4): flames are not extinguished unless the leaking gas is eliminated; safe havens identified; cylinder faced during approach and retreat (Oregon DPSST NFPA 1010 Firefighter II Task Book)Report a problem with this question
22. During a fire safety survey of a small business, you find an exit door chained shut. The owner declines your recommendation to remove the chain. Under NFPA 1010, what is your next step?
- A.Issue the owner a citation for the violation
- B.Refer the issue to the fire marshal or inspector✓ Answer
- C.Order the business closed until it is fixed
- D.Note it on the form and take no further action
A fire safety survey is not a code-enforcement inspection. The NFPA 1010 job performance requirement is that hazards are identified, recommendations are made to the occupant, and unresolved issues are referred to the proper authority. The power to cite or close a business belongs to the inspector or fire marshal under the local code, and simply noting the hazard leaves a blocked exit in place.
Ref QB-UPY79HSource: NFPA 1010 (2024) 7.5.1, Fire Fighter II (formerly NFPA 1001-2019 5.5.1): fire safety survey in an occupied structure; unresolved issues referred to the proper authority (Oregon DPSST NFPA 1010 Firefighter II Task Book)Report a problem with this question
23. You are sketching a preincident survey of a sprinklered warehouse. Engine crews will need to pump water into the sprinkler system during a fire. Which feature must the sketch show for that task?
- A.The fire alarm control panel location
- B.The post indicator valve location
- C.The fire department connection location✓ Answer
- D.The sprinkler riser main drain location
The fire department connection is the inlet where an engine pumps into the sprinkler system to supplement its water supply, so crews must be able to find it fast. The post indicator valve opens and closes the system's supply but is not where water is pumped in, the alarm panel only reports status, and the main drain is used for testing. NFPA 1010 requires the survey to cover water supply and fire protection systems, and department preplan criteria list the FDC, PIV and risers as separate items.
Ref QB-C76DUHSource: NFPA 1010 (2024) 7.5.3(A), Fire Fighter II (formerly NFPA 1001-2019 5.5.3): sources of water supply and fire suppression systems in the preincident survey (Oregon DPSST Task Book); Gresham Fire, Pre-Fire Plan Criteria (FDC, PIV, main risers as required data points)Report a problem with this question
24. Under NFPA 1010, a Fire Fighter II's preincident survey is complete when which outcome has been met?
- A.Occupant load approved and exit plan signed off
- B.Code violations cited and correction dates assigned
- C.Sprinkler and alarm systems tested and accepted
- D.Occupancy data recorded, concerns noted, site sketched✓ Answer
NFPA 1010 states the preincident survey is done so that all required occupancy information is recorded, items of concern are noted, and accurate sketches or diagrams are prepared. Its purpose is to plan operations for a future emergency, not to enforce the code. Citing violations, accepting fire protection systems and approving occupant loads are inspector or plans-review duties, not part of this firefighter JPR.
Ref QB-XP28SMSource: NFPA 1010 (2024) 7.5.3, Fire Fighter II (formerly NFPA 1001-2019 5.5.3): required occupancy information recorded, items of concern noted, accurate sketches or diagrams prepared (Oregon DPSST NFPA 1010 Firefighter II Task Book)Report a problem with this question
Other topics in this exam
Original practice questions written to the job performance requirements of NFPA 1010 (2024), which replaced NFPA 1001 for Fire Fighter I and II, and NFPA 470 for hazardous materials Awareness and Operations. Not affiliated with or endorsed by NFPA, IFSAC, the Pro Board, or any state fire academy. Each state writes its own certification exam — check your state's fire academy or certification office for its format and which edition it tests. NFPA 1010 standard →