Quibank app: now on the App Store — free, works offline. Get the app ↗

42 Department Operations & Safety Practice Questions & Answers

Every Department Operations & Safety practice question from the Sterile Processing (CRCST) Practice Test, with the correct answer and a short explanation.

Start practice test →

Practice tests

  1. 1. A facilities engineer tells you the sterile storage room now tests negative relative to the corridor outside it. Why does this matter?

    • A.Stored packages are now cooler than the adjoining corridor, so condensation is likely to form on the shelf surfaces
    • B.Room air now escapes outward too quickly, so the shelving collects dust from the ventilation exhaust system above
    • C.Each time the door opens, corridor air can flow in and carry airborne contaminants toward the stored packages✓ Answer
    • D.Negative pressure pulls moisture out of the wrappers, which shortens the event-related shelf life of every package

    Sterile storage is kept at positive pressure relative to surrounding areas so that air flows out when a door opens, which reduces the chance of airborne contamination. A negative reading reverses that direction and draws corridor air toward the packages.

    Ref QB-9HYSEBSource: Klacik S. "Keeping it sterile: Fundamentals of sterile storage," OR Manager, August 2023: air pressure positive in relation to surrounding areasReport a problem with this question

  2. 2. At the start of your shift, the sterile storage monitor shows humidity above the range in your facility's policy. What should you do?

    • A.Record the reading and report it right away to the person or department that facility policy designates✓ Answer
    • B.Move all the stored packages to the preparation area yourself and pull them for reprocessing before any case
    • C.Adjust the room humidity controls yourself, then log the corrected reading once it is back in range
    • D.Wait until the end of the shift and record only the final reading, in case the high value is a sensor error

    Facilities need a mechanism to identify and resolve HVAC variances, with retrievable records, so the technician's part is to document the reading and escalate it through the designated route. Adjusting the controls yourself, moving stock or holding back the reading bypasses that process, and a sensor's accuracy is for facilities staff to confirm after the report.

    Ref QB-QZEAP9Source: Chobin N. "Monitoring and Maintaining HVAC Parameters Within the Sterile Processing Department," Infection Control Today; Alberta Health Services SOP on temperature and humidity extremes in reprocessing and sterile storage areasReport a problem with this question

  3. 3. Overnight, temperature in a sterile processing work area drifted briefly outside the recommended range and has since recovered. Two coworkers disagree about what this means for the items in that area. How should the response be decided?

    • A.A multidisciplinary risk assessment weighs the size, duration and type of variance, because effects vary by situation✓ Answer
    • B.The sterilizer manufacturer decides, because its manual lists how long each room may remain outside the range
    • C.Every package is reprocessed automatically, because any excursion voids sterility regardless of how long it lasted
    • D.The shift lead decides alone from experience, because a recovered reading shows that no real exposure took place

    A small variance for a short time may or may not have clinical significance, so a multidisciplinary risk assessment, typically with engineering, sterile processing, perioperative services, infection prevention and risk management, determines the response. No single person's judgment or blanket rule fits every event.

    Ref QB-8HMF9ASource: Chobin N. "Monitoring and Maintaining HVAC Parameters Within the Sterile Processing Department," Infection Control Today (quoting AAMI ST79 on multidisciplinary risk assessment)Report a problem with this question

  4. 4. A new technician finds that two study guides list different temperature and humidity ranges for the decontamination area. Which values should the department actually work to?

    • A.The older AAMI table's values, since its room-by-room figures remain the fixed national limits for all departments
    • B.The sterilizer manual's values, since the equipment installed nearby determines what every work area must maintain
    • C.The newer guide's values, since the latest printed figures automatically replace a room's earlier design values
    • D.The facility's HVAC policy values, since engineering sets them from the ASHRAE 170 edition that applies to that space✓ Answer

    The room-by-room AAMI table was removed in the 2017 revision of ST79. Parameters now come from the version of ASHRAE 170 in effect when the area was built or renovated, and the facility and its engineering department set the monitoring policy, so a figure in a study guide does not govern a particular room.

    Ref QB-PZ3YG8Source: Chobin N. "Monitoring and Maintaining HVAC Parameters Within the Sterile Processing Department," Infection Control TodayReport a problem with this question

  5. 5. A coworker prepares to dry-mop the sterile storage floor because it is quicker and leaves no water near the shelves. What should you tell them?

    • A.Damp mop instead, because dry mopping sends dust into the air currents and onto the sterile packages✓ Answer
    • B.Wait for a weekly deep clean, because frequent floor cleaning disturbs packages more than dust does
    • C.Mist disinfectant over the shelves first, because airborne particles settle more slowly in damp air
    • D.Dry mop as planned, because any floor moisture will wick up through the shelving and wet the packages

    Sterile storage floors are damp mopped, because dry mopping puts dust into the air currents, and that dust then settles on surfaces including packages. Keeping the area clean, dry and free of dust protects package integrity.

    Ref QB-7H9549Source: Klacik S. "Keeping it sterile: Fundamentals of sterile storage," OR Manager, August 2023: processes to maintain cleanlinessReport a problem with this question

  6. 6. With hours left in the shift, blood splashes from a soiled tray onto the decontamination counter. Under the OSHA Bloodborne Pathogens Standard, when must that surface be decontaminated?

    • A.After the day's trays are finished, with plain water first, because disinfectant would harm nearby instruments
    • B.During the next housekeeping visit, because spills in this room are the environmental services team's duty
    • C.At the end of the shift with the routine wipe-down, because this whole room is handled as contaminated anyway
    • D.Immediately or as soon as feasible, with an appropriate disinfectant, because it is now overtly contaminated✓ Answer

    Contaminated work surfaces must be decontaminated with an appropriate disinfectant immediately or as soon as feasible when overtly contaminated or after any spill of blood or other potentially infectious materials. Routine end-of-shift cleaning is a separate requirement and does not replace this one.

    Ref QB-NZQMB7Source: OSHA 29 CFR 1910.1030(d)(4)(ii)(A)Report a problem with this question

  7. 7. A new enzymatic detergent has arrived, and you want to look up containment and cleanup steps for a spill before anyone needs them. Which section of its safety data sheet do you check?

    • A.Accidental Release Measures✓ Answer
    • B.Disposal Considerations
    • C.Stability and Reactivity
    • D.Handling and Storage

    Section 6, Accidental Release Measures, gives the recommended response to spills, leaks and releases, including containment and cleanup practices. The other named sections address routine storage, chemical stability and disposal rather than responding to a spill.

    Ref QB-6HWSW7Source: OSHA Brief "Hazard Communication Standard: Safety Data Sheets" (OSHA 3514), Section 6; OSHA 29 CFR 1910.1200(g)(2)Report a problem with this question

  8. 8. The department's only safety data sheet binder is locked in the manager's office, and the manager leaves at 5 p.m. An evening-shift technician raises this. What does the OSHA Hazard Communication Standard expect?

    • A.A manufacturer's phone line for after-hours requests, because suppliers rather than employers keep the sheets
    • B.Readily accessible copies on every shift, paper or electronic, because workers need them without barriers✓ Answer
    • C.The locked copy as it stands, because limiting the binder to supervisors keeps the sheets current and complete
    • D.Product labels alone after hours, because a container label carries the full content of a safety data sheet

    The employer must keep safety data sheets in the workplace and ensure they are readily accessible during each work shift to employees in their work areas. Electronic access is allowed as long as it creates no barrier to immediate access, and a locked office after hours is such a barrier.

    Ref QB-VZ7YHFSource: OSHA 29 CFR 1910.1200(g)(8)Report a problem with this question

  9. 9. A remodel plan would move the only eyewash unit from a room where staff handle corrosive high-level disinfectant to a locker room down the hall. How does the plan measure up against OSHA's requirement?

    • A.It falls short, because quick-drench or flushing facilities must be in the work area for immediate use✓ Answer
    • B.It is acceptable, because goggles are worn in that room and so the eyewash rule no longer applies there
    • C.It is acceptable, because any eyewash on the same floor counts as available once staff know the route
    • D.It falls short, because any renovated room must swap its eyewash for a full-body safety shower unit instead

    Where the eyes or body may be exposed to injurious corrosive materials, suitable facilities for quick drenching or flushing must be provided within the work area for immediate emergency use. Goggles reduce exposure but do not remove this requirement, and an eyewash down the hall delays flushing when seconds matter.

    Ref QB-DHD55GSource: OSHA 29 CFR 1910.151(c)Report a problem with this question

  10. 10. A full container of glutaraldehyde solution breaks on the floor and the vapor is quickly noticeable. You have no spill-response training or respirator. What should you do?

    • A.Stay and absorb it with towels from the sink, then bag them as regular trash and report it after your shift
    • B.Dilute it with running water from a hose, then mop it up yourself while wearing utility gloves and a mask
    • C.Open the corridor doors, run a floor fan and let the vapor clear before mopping the solution into a drain
    • D.Leave the area, close the doors, alert others and activate the facility's trained spill response team✓ Answer

    Any glutaraldehyde spill larger than small drips or splashes should be cleaned up by trained, properly equipped spill responders. OSHA guidance tells staff facing a large spill to close doors, alert others and activate the hazardous materials response, evacuating until the worksite is safe to reenter.

    Ref QB-N49QE3Source: OSHA, "Best Practices for the Safe Use of Glutaraldehyde in Health Care": general recommendations and large spillsReport a problem with this question

  11. 11. A preparation-and-packaging technician returns from vacation with polished artificial nails and says gloves will cover them anyway. Which response is correct?

    • A.Working outside decontamination makes them acceptable, because the risk exists only where soiled items are handled
    • B.Artificial nails and polish are not appropriate, because they can harbor bacteria and polish can chip onto instruments✓ Answer
    • C.Trimming them short makes them acceptable, because only long nails harbor bacteria or tear the packaging
    • D.Gloves make them acceptable, because an intact glove keeps all nail organisms away from whatever the wearer handles

    Reprocessing technicians should not wear artificial nails or nail polish, because artificial nails can harbor bacteria and polish can chip off into or onto instruments. The concern applies wherever packages and instruments are handled, not only in decontamination.

    Ref QB-5M3JU2Source: HSPA (IAHCSMM)/Purdue CRCST Self-Study Lesson 156, "Dress Code Considerations for Central Service"Report a problem with this question

  12. 12. A technician assembling trays keeps on a smooth wedding band and a wristwatch, reasoning that neither has loose parts. What does dress-code guidance say?

    • A.Only the band is a problem, because a watch worn above the glove cuff stays well away from the instruments
    • B.Both are a problem, because each can harbor organisms or catch on items, and the ring can also tear gloves✓ Answer
    • C.Only the watch is a problem, because a band without stones cannot catch on equipment or damage a glove
    • D.Neither is a problem, because smooth metal is cleaned by routine hand hygiene and cannot hold any organisms

    Jewelry and wristwatches should not be worn in the decontamination, preparation or sterilization areas: they are not easily cleaned, can harbor microorganisms and can fall into a tray or catch on items. Rings may also cause holes in gloves, so being smooth does not remove the concern.

    Ref QB-P4M2M4Source: HSPA (IAHCSMM)/Purdue CRCST Self-Study Lesson 156, "Dress Code Considerations for Central Service"Report a problem with this question

  13. 13. On break, a technician wears hospital-issued scrubs to a coffee shop across the street and then heads back to the preparation area. What is the correct practice?

    • A.Brush them off and do hand hygiene at the entrance, as hands rather than the fabric carry outside contaminants
    • B.Keep them on until the shift ends and launder them at home, as the contact with public areas was brief
    • C.Cover them with a clean warm-up jacket at the door, as an outer layer contains anything picked up outside
    • D.Change into fresh facility scrubs before reentering the semi-restricted area, as this set was worn in public✓ Answer

    Hospital-issued scrubs inadvertently worn in non-restricted public areas should be changed before returning to a semi-restricted area, and scrubs are not worn outside the workplace or laundered at home. This limits cross-contamination from outside and keeps outside soil out of the department.

    Ref QB-6MEVZ3Source: HSPA (IAHCSMM)/Purdue CRCST Self-Study Lesson 156, "Dress Code Considerations for Central Service", Objective 1Report a problem with this question

  14. 14. Operating room staff in street clothes often cut through sterile storage as a shortcut to the elevators. Which response reflects sound traffic control?

    • A.Allow the route if they walk straight through, since moving without touching packages poses no risk
    • B.Stop the practice, since only properly attired staff who need the sterile items should enter the room✓ Answer
    • C.Stop only the staff carrying bags, since belongings rather than people contaminate the stored items
    • D.Allow the route with shoe covers added, since only footwear brings outside contaminants into the room

    Sterile storage is a limited-access, semi-restricted area that should never be used as a shortcut through the department. Only properly attired personnel who need access to sterile items should be admitted, because people, air movement and traffic all contribute to package contamination.

    Ref QB-K4J24ZSource: HSPA (IAHCSMM)/Purdue CRCST Self-Study Lesson 151, "Handling and Storage of Sterile Packages", Objective 2; CDC/HICPAC Guideline for Disinfection and Sterilization, Storage of Sterile ItemsReport a problem with this question

  15. 15. To save steps, a technician proposes carrying freshly washed trays from the clean side back through decontamination to reach the sterilizers by a shorter path. How should this proposal be judged?

    • A.Reject it, because clean trays may enter decontamination only once they are wrapped and sterilized
    • B.Accept it, because trays that have been washed can no longer pick up contamination while being carried
    • C.Reject it, because items must keep moving from high-contamination areas toward clean and sterile ones✓ Answer
    • D.Accept it on closed carts, because a lid alone removes the need to keep clean and soiled traffic apart

    Workflow is designed so that devices clearly flow from high-contamination areas to clean and sterile areas, with contaminated and clean workspaces clearly separated. Physical barriers and airflow keep contamination inside the decontamination area, so sending cleaned trays back through it risks recontaminating them.

    Ref QB-3MCVGYSource: CDC, Summary of Infection Prevention Practices in Dental Settings, instrument processing workflow checklist item; CDC/HICPAC Guideline for Disinfection and Sterilization, Physical Facilities; HSPA CRCST Exam Content Outline (November 2023 revision) (one-way workflow)Report a problem with this question

  16. 16. A technician must lift a heavy instrument set from a low cart shelf. Which technique matches the body mechanics taught in HSPA's lesson on transporting soiled devices?

    • A.Feet together, standing close, bending at the waist, keeping the knees locked and pulling up with the lower back
    • B.Feet apart, standing close, bending at the knees, holding the set near the body and lifting slowly with the legs✓ Answer
    • C.Feet apart, standing back at arm's length, bending forward at the waist and straightening up fast with the load
    • D.Feet apart, standing close, bending at the knees, then twisting the back toward the cart while rising with the set

    Safe lifting uses a wide base of support, standing close to the object, bending at the knees rather than the waist, holding the load close and lifting slowly with the hips and legs. Twisting the back while lifting strains muscles and ligaments and is what the lesson warns against.

    Ref QB-M4WC92Source: HSPA/Purdue CRCST Self-Study Lesson 194, "Proper Handling and Transport of Soiled Medical Devices" (ergonomics and body mechanics)Report a problem with this question

  17. 17. You are deciding where to place a heavy wrapped instrument set and a lightweight peel pack on a storage rack. Which arrangement is best for safe handling?

    • A.Heavy set on the floor below the rack and light pack above, since that avoids lifting it onto any shelf
    • B.Heavy set on the top shelf and light pack lower, since gravity makes bringing the set down the easier job
    • C.Heavy set on a middle shelf and light pack up higher, since that keeps the lift close to your power zone✓ Answer
    • D.Heavy set on the lowest shelf and light pack in the middle, since bottom shelves are the strongest ones

    For safety and ease of handling, heavy trays go on middle shelves and lightweight packages on higher shelves, which keeps heavy lifts above the knees, below the shoulders and close to the body. Sterile items also must never be stored on the floor.

    Ref QB-4MQ7PZSource: Klacik S. "Keeping it sterile: Fundamentals of sterile storage," OR Manager, August 2023: storage of heavy trays; Cal/OSHA-NIOSH Ergonomic Guidelines for Manual Material Handling (NIOSH 2007-131), power zoneReport a problem with this question

  18. 18. A vendor offers the department a new chemical indicator for steam sterilization and says it is ready to sell to hospitals. Which body had to review the product before that sale, and in what capacity?

    • A.AAMI, which regulates indicators as sterile goods and reviews a premarket submission
    • B.ISO, which regulates indicators as global products and reviews a premarket submission
    • C.CMS, which regulates indicators as hospital supplies and reviews a premarket submission
    • D.FDA, which regulates indicators as medical devices and reviews a premarket submission✓ Answer

    Chemical indicators are Class II medical devices under FDA regulation, so the manufacturer must submit a premarket submission for FDA review before selling them to health care facilities. ISO compliance claims, by contrast, are self-certified by the manufacturer.

    Ref QB-S4P258Source: HSPA CRCST Self-Study Lesson 185, Chemical Indicator Classifications: What Technicians Need to KnowReport a problem with this question

  19. 19. A new technician asks how the Centers for Medicare & Medicaid Services (CMS) can hold a hospital's sterile processing department to infection prevention requirements when CMS does not clear any device. What is the basis for that authority?

    • A.Premarket clearances that a hospital must hold to buy and keep using each sterilizer and indicator
    • B.Conditions of Participation that a hospital must meet to begin and continue in Medicare and Medicaid✓ Answer
    • C.Consensus standards that a hospital must adopt word for word to keep its state business license
    • D.Workplace safety rules that a hospital must post to protect employees from bloodborne pathogens

    CMS develops Conditions of Participation that organizations must meet to begin and continue participating in Medicare and Medicaid, and its surveyors assess sterilization practices against the hospital condition on infection prevention. Device clearance belongs to FDA, and workplace safety rules belong to OSHA.

    Ref QB-9MGVH7Source: CMS, Conditions for Coverage & Conditions of Participation; CMS Survey & Certification Memo S&C 14-44 on Immediate Use Steam Sterilization; 42 CFR 482.42Report a problem with this question

  20. 20. During an in-service, a technician says, "ANSI/AAMI ST79 is a federal law, so an inspector can fine us directly for not following it." Which correction is accurate?

    • A.It is a consensus standard, which is not itself a law but serves as a basis for department policies✓ Answer
    • B.It is a federal regulation, which FDA enforces directly against a hospital through fines per missed step
    • C.It is a CMS condition, which applies to hospitals alone and becomes binding during a Medicare survey
    • D.It is a clinical guideline, which applies to operating rooms alone and carries no weight in the department

    ST79 is a consensus document developed by a standards development organization with stakeholders that include sterile processing staff and regulators. A standard is not itself a regulation, although it may repeat legal requirements; it serves as a basis for facility and departmental policies, and the facility's own policy then carries it into daily work.

    Ref QB-XM6UMRSource: HSPA CRCST Self-Study Lesson 195, Applying Standards in Sterile Processing: What Technicians Must KnowReport a problem with this question

  21. 21. A technician drafting a procedure from a standard sees the words "shall," "should" and "may" in three different statements. What do those words express, in that order?

    • A.A permission, a recommendation and a requirement
    • B.A requirement, a permission and a recommendation
    • C.A recommendation, a requirement and a permission
    • D.A requirement, a recommendation and a permission✓ Answer

    As listed from ANSI/AAMI ST79 in the HSPA lesson, "shall" expresses a requirement, "should" a recommendation and "may" a permission. The distinction matters because a department policy has to carry the same strength of language as the standard it draws on.

    Ref QB-F5CZ7SSource: HSPA CRCST Self-Study Lesson 195, Applying Standards in Sterile Processing: What Technicians Must KnowReport a problem with this question

  22. 22. A department's written procedure for a device says one thing, and the current manufacturer's instructions for use (IFU) for that device say something different. Under the Joint Commission's hierarchy for infection prevention requirements, how do the two rank?

    • A.The policy ranks above the IFU, so the department should keep the procedure as written
    • B.The two rank equally, so the department should choose the more conservative of the pair
    • C.The IFU rank above the policy, so the department should change the procedure to match✓ Answer
    • D.The two rank by date, so the department should apply whichever of them was issued later

    The hierarchy places laws and regulations first, then CMS requirements, then manufacturers' written IFU, then evidence-based guidelines and national standards, then consensus documents, and the organization's own policies last. A department policy that departs from a current IFU therefore has to be corrected.

    Ref QB-YMH6TSSource: HSPA CRCST Self-Study Lesson 195, Applying Standards in Sterile Processing: What Technicians Must Know, Table 3 (Joint Commission hierarchy)Report a problem with this question

  23. 23. A patient is seriously injured, and the facility has information suggesting that a reusable device contributed to the injury. Under the FDA Medical Device Reporting rule, where does the facility's report of this serious injury go?

    • A.To the device manufacturer, or to FDA if the manufacturer is not known✓ Answer
    • B.To CMS first, with FDA told only if a survey confirms the device failed
    • C.To the state health board, or to OSHA if the state has no device program
    • D.To FDA alone, with the manufacturer told only if FDA asks for that step

    A user facility reports a device-related serious injury to the manufacturer, and to FDA only when the manufacturer is unknown. The rule differs for a device-related death, which goes to both FDA and the manufacturer, so the type of event decides the recipient.

    Ref QB-G5QBDTSource: 21 CFR 803.30; FDA, Mandatory Reporting Requirements: Manufacturers, Importers and Device User FacilitiesReport a problem with this question

  24. 24. After a bloodborne pathogens in-service, the only record kept is a sheet of attendee signatures. Under the OSHA standard, what must this training record contain?

    • A.Session dates, a content summary, trainers' names and qualifications, and attendees' names and job titles✓ Answer
    • B.Session length, a content summary, the supervisor's approval, and attendees' names and department codes
    • C.Session dates, a quiz score, trainers' names and licenses, and attendees' names and vaccination status
    • D.Session costs, a handout copy, the sponsor's name and address, and attendees' names and years of service

    The bloodborne pathogens standard specifies four elements for a training record: the dates of the sessions, the contents or a summary of them, the names and qualifications of those conducting the training, and the names and job titles of those attending. A signature sheet alone cannot show what was taught or who taught it.

    Ref QB-VMF6APSource: OSHA 29 CFR 1910.1030(h)(2), Training RecordsReport a problem with this question

  25. 25. A technician's puncture from a contaminated sharp is entered in the employer's sharps injury log. What must the entry capture, and how must it be kept?

    • A.Employee's name and vaccine history, shift, and how it happened, kept so the supervisor can review the person
    • B.Device type and brand, work area, and how it happened, kept so the employee's confidentiality is protected✓ Answer
    • C.Source patient's name and diagnosis, work area, and how it happened, kept so infection risk can be traced
    • D.Device lot and expiration date, employee's name, and how it happened, kept so a recall can be opened quickly

    The standard sets the minimum content of the log for percutaneous injuries: the type and brand of device, the department or work area, and an explanation of how the incident occurred. OSHA also requires it to be maintained in a way that protects the injured employee's confidentiality.

    Ref QB-D5NBVPSource: OSHA 29 CFR 1910.1030(h)(5), Sharps injury logReport a problem with this question

  26. 26. A preceptor teaches a new hire each task in the preparation and packaging area. An accreditation surveyor may later ask to see the onboarding records. What documentation should exist?

    • A.A certificate from the new hire's outside course, standing in for any department training records
    • B.A signoff with the preceptor for each taught task, on paper or in an electronic tracking system✓ Answer
    • C.A single signoff by the manager at the end of orientation, covering all tasks in one general line
    • D.A verbal confirmation from the preceptor for each taught task, given when the surveyor asks for it

    New hires should complete a process and signoff with a preceptor for each taught task, collected either electronically or on paper. Auditing agencies often request these documents to check onboarding and continuing education, so a per-task record is what shows the training actually took place.

    Ref QB-WMTGFQSource: HSPA CRCST Self-Study Lesson 186, Sterile Processing Onboarding 101Report a problem with this question

  27. 27. A surveyor checks load documentation. The department logs some cycles in a paper binder and others in an electronic tracking system, and a few days have no entry in either. What is the documentation expectation?

    • A.One method, paper or electronic, completed for implant loads and left optional for others
    • B.Both methods, paper and electronic, completed for every load to give surveyors a backup
    • C.Both methods, paper and electronic, completed once a week from the printouts on the sterilizer
    • D.One method, paper or electronic, completed with no gaps and traceable to the patient✓ Answer

    The HSPA survey-readiness lesson describes documentation completed with no gaps in a paper or an electronic tracking system, not both, with product identification and traceability to the patient. Splitting records across two systems invites exactly the gaps that break the trace back from a patient to a load.

    Ref QB-E5ZN2RSource: HSPA CRCST Self-Study Lesson 176, Accreditation Survey Preparedness for Sterile Processing ProfessionalsReport a problem with this question

  28. 28. A department's only copy of its policy and procedure manual is locked in the manager's office, and night-shift technicians cannot reach it. What is the correct expectation for these documents?

    • A.Keep them with the manager alone, since they are controlled and meant for reading at a formal review
    • B.Keep them in infection prevention, since that department owns each task and answers staff questions
    • C.Keep them readily available to all staff, since they are used to train and to guide consistent practice✓ Answer
    • D.Keep them in the accreditation file, since they are written mainly to satisfy surveyors on a site visit

    Policies and procedures translate laws, standards and IFU into the way each task is done, and they help ensure every staff member performs it the same way. HSPA states they should be used to train, support competency assessment and be readily available to all staff, which a locked single copy prevents.

    Ref QB-TMRGXKSource: HSPA CRCST Self-Study Lesson 195, Applying Standards in Sterile Processing: What Technicians Must KnowReport a problem with this question

  29. 29. Technicians walk back and forth across the preparation area for supplies, and sets sit on a cart waiting for a step that adds nothing to their quality. The team wants to remove these wasted steps. Which approach fits this goal?

    • A.Six Sigma, because it attempts to reduce variation and defects
    • B.Tray auditing, because it attempts to find defects in finished sets
    • C.Lean, because it attempts to eliminate waste within a process✓ Answer
    • D.IUSS tracking, because it attempts to count abbreviated steam cycles

    AHRQ describes Lean as attempting to eliminate waste within a process, which is exactly what unnecessary walking and waiting are. Six Sigma is aimed at variation and defects, and audits or tracking measure results rather than removing steps.

    Ref QB-B5XNHMSource: AHRQ Workflow Assessment for Health IT Toolkit, Lean Six Sigma; HSPA CRCST Exam Content Outline (November 2023 revision), Section 1, Quality AssuranceReport a problem with this question

  30. 30. A Six Sigma team has defined a problem with incorrect count sheets, measured the error rate, analyzed the causes, and piloted and implemented a solution with good results. What does the next phase call for?

    • A.Control, which maintains the gains after the solution is in place✓ Answer
    • B.Define, which restates the project now that the solution is in place
    • C.Measure, which records the current state before the solution is in place
    • D.Analyze, which searches again for causes now the solution is in place

    The Six Sigma sequence is define, measure, analyze, improve and control. Piloting and implementing a solution is the improve phase, so what remains is control, which keeps the gains from eroding once attention moves elsewhere.

    Ref QB-2Q6Z5VSource: AHRQ Workflow Assessment for Health IT Toolkit, Six SigmaReport a problem with this question

  31. 31. A team using a Plan-Do-Study-Act cycle has just tried a new tray-labeling step on one shift for two weeks. What belongs in the Study step?

    • A.Write the change into policy for all shifts, to lock the new plan in place
    • B.Set a new goal and success metrics, to start building the following plan
    • C.Repeat the labeling step on that same shift, to give the plan more time
    • D.Monitor outcomes for progress or problems, to test whether the plan is valid✓ Answer

    In the PDSA cycle, Study means monitoring outcomes to test the plan's validity and to look for signs of progress, success or problems. Small tests are analyzed before a change is implemented more broadly, and goals are set in Plan rather than in Study.

    Ref QB-H7ZTJUSource: AHRQ CAHPS Ambulatory Care Improvement Guide, Section 4: Ways To Approach the Quality Improvement ProcessReport a problem with this question

  32. 32. A monthly quality report tracks each Immediate Use Steam Sterilization (IUSS) cycle by item and by reason. What is the quality purpose of tracking it this way?

    • A.To measure the time it saves and identify which items can move to this cycle permanently
    • B.To compare the rate with a benchmark and expose repeat items that need a plan to address them✓ Answer
    • C.To record surgeons' preferences and list who may order this cycle without giving any reason
    • D.To confirm that each cycle replaces biological monitoring and justify dropping its indicators

    The outline names IUSS among quality assurance benchmarks, and surveyors ask how IUSS is used and why, whether the same items recur, whether plans exist to address them and what the benchmark rate is. Item and reason data answer those questions and point to the sets that need attention.

    Ref QB-ZPTNYTSource: HSPA CRCST Self-Study Lesson 176, Accreditation Survey Preparedness for Sterile Processing Professionals; HSPA CRCST Exam Content Outline (November 2023 revision), Section 1, Quality AssuranceReport a problem with this question

  33. 33. A surveyor picks a set in the operating room and follows it back through point of use, transport, decontamination, assembly, sterilization and storage, questioning staff along the way. What is this assessment method, and what does it do?

    • A.A tray audit, which opens finished sets in storage to check contents against count sheets
    • B.A recall review, which follows a failed load back to identify each patient who received it
    • C.A tracer audit, which follows a process in real time to check compliance with standards✓ Answer
    • D.A turnaround study, which times the steps of a set in real time to find process delays

    Tracer methodology is a real-time assessment tool that follows a patient or a process through the facility to address compliance with standards and evidence-based guidelines. It moves along the actual path of the work, so it can surface gaps at any handoff, and departments can run their own tracers too.

    Ref QB-G7NGDTSource: HSPA CRCST Self-Study Lesson 176, Accreditation Survey Preparedness for Sterile Processing ProfessionalsReport a problem with this question

  34. 34. Operating room staff report that several deliveries of supplies and instruments picked for scheduled surgeries this month arrived with items missing or with items meant for a different procedure. Which quality assurance benchmark tracks this problem?

    • A.IUSS tracking, which compares abbreviated steam cycles with the total number of loads run
    • B.Inventory fill rates, which compare the stock that a unit requests with what is delivered
    • C.Surgical case cart accuracy, which compares the cart contents with what the procedure requires✓ Answer
    • D.Instrument set turnaround time, which compares processing time with when the set is needed

    The content outline lists surgical case cart accuracy alongside tray audits, IUSS, instrument set turnaround times and inventory fill rates as quality assurance benchmarks. Missing or wrong cart contents are a cart accuracy failure, since the delivery may be on time and the stock may be available while the cart is still built wrong.

    Ref QB-YPFBTSSource: HSPA CRCST Exam Content Outline (November 2023 revision), Section 1, Quality Assurance benchmarksReport a problem with this question

  35. 35. An SPD buyer is choosing a disinfectant for decontamination countertops and transport carts, which are noncritical surfaces. What should the product label show to confirm it is legally marketed for this use?

    • A.OSHA approval for workplace use
    • B.CDC listing as a recommended agent
    • C.EPA registration number under FIFRA✓ Answer
    • D.FDA 510(k) clearance for devices

    Disinfectants for environmental (noncritical) surfaces are pesticides under FIFRA, so the EPA must register them before sale, and the label carries an EPA registration number. Under the FDA-EPA division of authority, FDA clears liquid chemical sterilants and high-level disinfectants used on critical and semicritical devices. EPA keeps disinfectants for noncritical surfaces. OSHA does not approve products, and CDC publishes guidance but does not license anything.

    Ref QB-F7A68SSource: CDC Guideline for Disinfection and Sterilization in Healthcare Facilities (2008, updated 2024), Regulatory Framework section (p. 57): EPA registers disinfectants under FIFRA; FDA regulates liquid chemical sterilants on critical/semicritical devicesReport a problem with this question

  36. 36. An SPD receives an FDA-posted recall notice for a lot of sterilization wrap, labeled "Class I." What does that recall classification mean?

    • A.Lowest-risk device type, needs no FDA review
    • B.Reasonable chance of serious harm or death✓ Answer
    • C.Possible temporary or reversible health harm
    • D.Unlikely to cause adverse health consequences

    FDA recall classes run opposite to device classes. A Class I recall is the most serious: there is a reasonable probability that using the product will cause serious adverse health consequences or death. Class II covers temporary or medically reversible harm, and Class III covers products unlikely to cause harm. A Class I device, on the other hand, is the lowest-risk device category, which is why candidates mix the two up.

    Ref QB-XP4ZMRSource: FDA, Recalls Background and Definitions (fda.gov): Class I, II and III recall definitionsReport a problem with this question

  37. 37. An SPD that runs an ethylene oxide sterilizer has staff wear badges to measure breathing-zone exposure. Which agency sets the 1 ppm 8-hour time-weighted average limit that the results are compared against?

    • A.EPA
    • B.FDA
    • C.CDC
    • D.OSHA✓ Answer

    OSHA protects workers, and its ethylene oxide standard (29 CFR 1910.1047) requires employers to keep employee exposure at or below 1 ppm as an 8-hour TWA, with a separate excursion limit. EPA deals with EtO emissions to the outside environment, not employee breathing-zone limits. FDA clears the sterilizer as a device, and CDC publishes guidelines without enforcement power.

    Ref QB-E7XT2RSource: OSHA 29 CFR 1910.1047(c)(1), Ethylene oxide permissible exposure limit: 1 ppm 8-hour TWAReport a problem with this question

  38. 38. An SPD manager is briefing staff before an unannounced survey by The Joint Commission. Which statement correctly describes The Joint Commission's role?

    • A.Private accreditor whose survey can grant CMS deemed status✓ Answer
    • B.Federal agency that writes Medicare conditions of participation
    • C.Government regulator that clears sterilizers before sale
    • D.Standards body that publishes ANSI-approved steam standards

    The Joint Commission is a private, voluntary accrediting organization, not a government agency. Under CMS rules, a hospital that voluntarily earns accreditation from a CMS-approved accrediting organization gets deemed status, meaning CMS certifies it for Medicare participation based on that accreditation. CMS writes the Conditions of Participation, FDA clears sterilizers, and AAMI writes the ANSI-approved standards such as ST79.

    Ref QB-WPRNFQSource: 42 CFR 488.1, definition of "Deemed status" (Medicare certification based on voluntary accreditation by a CMS-approved national accrediting organization)Report a problem with this question

  39. 39. A facilities engineer is reviewing the HVAC design for a new soiled workroom/decontamination room. Under ASHRAE 170, how must the room's air be handled?

    • A.Half the air is recirculated to save energy
    • B.Air is returned to the general building system
    • C.Air is HEPA-filtered and recirculated to prep
    • D.All room air is exhausted directly outdoors✓ Answer

    ASHRAE 170 marks the soiled workroom/decontamination room "Yes" for all room air exhausted directly to outdoors. This keeps aerosols and chemical vapors from contaminated instruments out of the building's return air and away from clean areas. Recirculating any of it, even after filtering, would let decontamination air reach clean spaces. That is why the clean assembly and sterile storage rows carry no exhaust requirement but the decon row does.

    Ref QB-D7KGVPSource: ANSI/ASHRAE/ASHE Standard 170-2021, Addendum o, Table 7-1 Sterile Processing: Soiled workroom/decontamination room, all room air exhausted directly to outdoors = YesReport a problem with this question

  40. 40. A new SPD layout is being air-balanced. Which pressure plan, relative to adjacent spaces, matches ASHRAE 170 for decontamination, clean assembly (prep/pack) and sterile storage?

    • A.Decon positive; prep and sterile storage negative
    • B.Decon negative; prep and sterile storage positive✓ Answer
    • C.Decon negative; prep and sterile storage neutral
    • D.Decon negative; prep positive; storage negative

    Air should move from clean to dirty. ASHRAE 170 lists the clean assembly/workroom and the sterile storage room as positive, so air pushes out and dust or contaminants do not drift in onto clean and sterile packages. The soiled/decontamination room is negative, so air is pulled in and contaminated air stays contained. A neutral or negative sterile storage room would let corridor air flow in over sterile items.

    Ref QB-RG6HKHSource: ANSI/ASHRAE/ASHE Standard 170-2021, Addendum o, Table 7-1 Sterile Processing: clean assembly/workroom Positive; soiled workroom/decontamination Negative; sterile storage room PositiveReport a problem with this question

  41. 41. A soiled workroom/decontamination room is being designed to ASHRAE 170-2021. What is the minimum total air change rate for this room?

    • A.2 total air changes per hour
    • B.4 total air changes per hour
    • C.6 total air changes per hour✓ Answer
    • D.12 total air changes per hour

    ASHRAE 170-2021 sets the decontamination room at a minimum of 6 total air changes per hour, 2 of which must be outdoor air. That is why 2 is a near-miss: it is the outdoor-air minimum, not the total. 4 total ACH is the minimum for clean assembly and sterile storage. Older references (for example, the AAMI value cited in the CDC 2008 guideline) give 10 ACH, and a facility is held to the ASHRAE edition in force when its system was built or renovated.

    Ref QB-9ZBP6JSource: ANSI/ASHRAE/ASHE Standard 170-2021, Addendum o, Table 7-1 Sterile Processing: Soiled workroom/decontamination room, minimum outdoor ACH 2, minimum total ACH 6Report a problem with this question

  42. 42. An SPD logs temperature daily in its clean assembly (prep and packaging) workroom. Which design temperature range does ASHRAE 170 set for this room?

    • A.68–73°F (20–23°C)✓ Answer
    • B.60–73°F (16–23°C)
    • C.72–78°F (22–26°C)
    • D.Up to 75°F (24°C)

    ASHRAE 170 sets the clean assembly/workroom at 68–73°F (20–23°C) with relative humidity at a maximum of 60%. That range keeps packaging staff comfortable in cover garments while limiting moisture on packaging materials. 60–73°F is the decontamination room range (cooler, for staff in heavy PPE), a maximum of 75°F applies to sterile storage, and 72–78°F is the range for general clean supply storage.

    Ref QB-QGT6EGSource: ANSI/ASHRAE/ASHE Standard 170-2021, Addendum o, Table 7-1 Sterile Processing: Clean assembly/workroom design temperature 68–73°F/20–23°C, RH max 60Report a problem with this question

Other topics in this exam

Practice questions based on the HSPA CRCST Certification Exam Content Outline, ANSI/AAMI ST79 sterility-assurance practice, and CDC/HICPAC disinfection and sterilization guidance. CRCST is a mark of the Healthcare Sterile Processing Association; this site is not affiliated with or endorsed by HSPA. Always follow the device manufacturer's written instructions for use, your facility's policies, and the current edition of the applicable standards. About the CRCST exam →