Quibank app: now on the App Store — free, works offline. Get the app ↗

31 Interior, Life Safety & Built-in Appliances Practice Questions & Answers

Every Interior, Life Safety & Built-in Appliances practice question from the Home Inspector Practice Test (NHIE), with the correct answer and a short explanation.

Start practice test →
  1. 1. A second-floor bedroom has a casement window whose net clear opening measures 24 in high by 20 in wide. How should the inspector evaluate it as an emergency escape and rescue opening?

    • A.Acceptable: it meets the 24 in and 20 in minimums
    • B.Deficient: its net clear width must be 24 in
    • C.Deficient: its net clear area is below 5.7 sq ft✓ Answer
    • D.Acceptable: 5.0 sq ft applies to any upper floor

    The height and width minimums (24 in and 20 in) are separate from the area minimum. 24 x 20 = 480 sq in, only about 3.33 sq ft, far short of the 5.7 sq ft net clear opening that IRC R310.2.1 requires. The 5.0 sq ft exception applies only to grade-floor openings, not upper floors, so the window should be reported as a deficient escape opening.

    Ref QB-RRDJJNSource: 2021 IRC R310.2.1 Minimum size (5.7 sq ft; 5 sq ft grade-floor exception) and R310.2.2 Minimum dimensions (24 in H, 20 in W)Report a problem with this question

  2. 2. In a bedroom, the escape window's net clear opening area is adequate, but the bottom of the clear opening is 48 in above the finished floor. What should the report say?

    • A.Sill exceeds the 44 in maximum; report as a safety defect✓ Answer
    • B.Sill is within the 48 in maximum; no defect to report
    • C.Sill height matters only for basement escape windows
    • D.Sill is acceptable because the window area is adequate

    IRC R310.2.3 limits the bottom of an emergency escape and rescue opening to 44 in above the floor, because occupants, including children, must be able to climb out quickly and firefighters must be able to enter. Adequate area does not offset a high sill, and the limit applies to every sleeping room, not only basements, so a 48 in sill is reported as a life-safety defect.

    Ref QB-A9X2BQSource: 2021 IRC R310.2.3 Maximum height from floor (44 in)Report a problem with this question

  3. 3. Measuring an interior stair flight, the inspector finds every riser is 7-1/4 in except the bottom riser, which is 7-3/4 in. What is the best report statement?

    • A.No defect: every riser is within the 7-3/4 in limit
    • B.Defect: riser heights vary by more than 3/8 in✓ Answer
    • C.No defect: up to 3/4 in variation is allowed
    • D.Defect: the bottom riser exceeds the 7-1/2 in limit

    Each riser is within the 7-3/4 in maximum, but IRC R311.7.5.1 also says the greatest riser in a flight may not exceed the smallest by more than 3/8 in. Here the difference is 1/2 in. Uneven risers break the rhythm people rely on and cause trips, so the inconsistency is a reportable safety defect.

    Ref QB-SRRVQPSource: 2021 IRC R311.7.5.1 Risers (7-3/4 in max; 3/8 in max variation within a flight)Report a problem with this question

  4. 4. An interior loft overlooks the living room 9 ft below. Its guard is 36 in high, but the balusters leave 5-1/2 in clear openings between them. What should the inspector report?

    • A.Acceptable: openings up to 6 in are permitted
    • B.Acceptable: the 36 in height meets the guard rule
    • C.Safety defect: the guard must be 42 in high
    • D.Safety defect: openings must stop a 4 in sphere✓ Answer

    A guard is required because the loft is more than 30 in above the floor below, and 36 in meets the residential height rule. But IRC R312.1.3 bars openings that let a 4 in sphere pass, roughly the size of a small child's head. The 6 in sphere applies only to the triangle under a stair guard, so 5-1/2 in gaps are a fall hazard to report.

    Ref QB-B9ADGRSource: 2021 IRC R312.1.1 Where required (30 in), R312.1.2 Height (36 in), R312.1.3 Opening limitations (4 in sphere; 6 in stair triangle)Report a problem with this question

  5. 5. The door between an attached garage and the kitchen is a hollow-core wood interior door with no closer. Which statement best describes the condition?

    • A.Defect; recommend a compliant self-closing, self-latching door✓ Answer
    • B.Acceptable, because the garage wall has 1/2 in gypsum board
    • C.Acceptable, because any solid or hollow wood door qualifies
    • D.Defect only if a bedroom is located directly above the garage

    The garage is the likeliest place for a fire to start, so the door in the separation must resist it. IRC R302.5.1 accepts only solid wood or solid- or honeycomb-core steel doors at least 1-3/8 in thick, or a 20-minute fire-rated door, and the 2021 text requires it to be self-latching with a self-closing or automatic-closing device. A hollow-core wood door with no closer breaks the separation no matter how the wall is finished.

    Ref QB-TR48WQSource: 2021 IRC R302.5.1 Opening protection (garage-to-dwelling doors)Report a problem with this question

  6. 6. An all-electric house (electric furnace, water heater, range and dryer) has an attached garage with a door into the laundry room. Under the 2021 IRC new-construction rule, are carbon monoxide alarms required?

    • A.No, because no fuel-fired appliance exists in the dwelling
    • B.No, because CO alarms are required only near gas furnaces
    • C.Yes, because the attached garage communicates with the house✓ Answer
    • D.Yes, but only inside the laundry room next to the garage door

    IRC R315.2.1 has two separate triggers for CO alarms: a fuel-fired appliance in the dwelling, or an attached garage with an opening into the dwelling. A running car in the garage can push CO through that door, so either trigger alone is enough. The alarms go outside each separate sleeping area near the bedrooms (R315.3), not beside the garage door.

    Ref QB-C9NQNSSource: 2021 IRC R315.2.1 New construction (CO alarm triggers) and R315.3 LocationReport a problem with this question

  7. 7. A two-story house has a finished basement and a crawl space under a rear addition. Under 2021 IRC R314.3, which location does NOT require a smoke alarm?

    • A.Each bedroom on the upper floor
    • B.The crawl space under the addition✓ Answer
    • C.The hallway outside the bedrooms
    • D.The finished basement level

    IRC R314.3 requires smoke alarms in each sleeping room, outside each separate sleeping area near the bedrooms, and on each story including basements and habitable attics. It expressly excludes crawl spaces and uninhabitable attics, because no one lives or sleeps there.

    Ref QB-URFJ3SSource: 2021 IRC R314.3 Location (smoke alarms)Report a problem with this question

  8. 8. Under the kitchen sink, the dishwasher drain hose lies along the cabinet floor and connects directly to the disposer inlet. Nothing in the installation provides an air gap. What should the inspector report?

    • A.Acceptable: the disposer prevents any backflow
    • B.Defect: the hose needs its own separate trap
    • C.Acceptable: a high loop is only needed on new work
    • D.Defect: the hose needs a high loop or an air gap✓ Answer

    IRC P2717.2 requires the dishwasher discharge to rise to the underside of the counter and be fastened there before it connects to the disposer or sink tailpiece; P2717.1 alternatively accepts an air gap or backflow preventer. A hose lying low lets dirty sink water flow back into the dishwasher. The NHIE outline names an incorrectly installed dishwasher drain loop as a typical defect.

    Ref QB-596DFHSource: 2021 IRC P2717.2 Sink and dishwasher (discharge rises to underside of counter); P2717.1; NHIE 2023 content outline Task 11DReport a problem with this question

  9. 9. In a home with a residential fire sprinkler system, several pendant sprinkler heads were painted over when the ceilings were repainted. What should the inspector recommend?

    • A.Replacement of the painted heads with new listed heads✓ Answer
    • B.Careful cleaning of the paint off each sprinkler head
    • C.No action, since paint does not affect sprinkler operation
    • D.A flow test of the system to confirm the heads still open

    Paint can insulate or glue the heat-sensitive element so the head opens late or not at all, and cleaning cannot prove it will work. IRC P2904.2.6 therefore prohibits painting sprinklers and requires painted, caulked, modified or damaged heads to be replaced with new ones. The inspector reports the condition and refers it to a qualified fire sprinkler contractor; a flow test is outside a visual inspection.

    Ref QB-MRY7VGSource: 2021 IRC P2904.2.6 Sprinkler modifications prohibited; NHIE 2023 content outline Task 13.4Report a problem with this question

  10. 10. While inspecting a home built before 1978, the inspector is asked by the client to confirm whether the interior paint contains lead. The inspector works under a standard of practice such as InterNACHI's. What is the most appropriate response?

    • A.Scrape a paint chip and report the result from a home test kit
    • B.State that paint applied before 1978 is always lead-based paint
    • C.Explain it is outside the inspection; refer to a lead specialist✓ Answer
    • D.Report the paint as lead-free if no peeling or chalking is seen

    A home inspection is a visual, non-invasive survey. The InterNACHI Standards of Practice list environmental hazards, including lead paint, and airborne hazards such as radon as things the inspector is not required to determine. Visual condition cannot prove whether paint contains lead, and not every pre-1978 home has it, so the right step is to explain the limit and refer the client to a qualified lead inspector or risk assessor.

    Ref QB-XHVFRUSource: InterNACHI Home Inspection Standards of Practice, Limitations/Exclusions (not required to determine radon or environmental hazards including lead paint)Report a problem with this question

  11. 11. An interior stair with 12 risers has one continuous handrail. Measured vertically from the sloped plane of the tread nosings, the rail is 32 in high. What should the inspector report?

    • A.Acceptable: handrails may be 30 to 38 in high
    • B.Deficient: the rail is below the 34 in minimum✓ Answer
    • C.Deficient: rails are required on both sides
    • D.Acceptable: height limits apply to guards only

    IRC R311.7.8.1 sets stair handrail height at 34 in minimum and 38 in maximum, measured vertically from the sloped plane adjoining the tread nosings, so a 32 in rail is too low to catch a person who stumbles. The 30 to 34 in range applies only to alternating tread devices and ship's ladders. R311.7.8 requires a handrail on at least one side of a flight with four or more risers, so one side is enough here.

    Ref QB-F23NBVSource: 2021 IRC R311.7.8 Handrails (one side, 4 or more risers) and R311.7.8.1 Height (34 to 38 in)Report a problem with this question

  12. 12. A bathroom window sits in the wall directly above a bathtub. The bottom edge of the glass is 42 in above the tub floor, and no safety-glazing mark appears on the pane. How should the inspector report it?

    • A.Acceptable: the pane is under the 9 sq ft trigger
    • B.Acceptable: its bottom edge is above the 18 in limit
    • C.Defect: glass below 60 in at a tub needs safety glazing✓ Answer
    • D.Defect: safety glass here must be tempered, not laminated

    IRC R308.4.5 makes glazing in walls or enclosures containing or adjacent to bathtubs and showers a hazardous location when its bottom exposed edge is less than 60 in above any standing or walking surface, because a person who slips in a wet tub can fall into the glass. The tub floor is the standing surface, so 42 in falls inside the rule. The 9 sq ft and 18 in figures belong to the separate window test in R308.4.3, and laminated glass is an accepted safety glazing, so the inspector reports the unmarked pane as a safety concern for correction.

    Ref QB-YH8TWVSource: 2021 IRC R308.4.5 Glazing and wet surfaces (bottom edge less than 60 in above standing surface); R308.4.3 Glazing in windowsReport a problem with this question

  13. 13. The hallway smoke alarm outside the bedrooms is mounted 18 in horizontally from the door of a bathroom that has a shower, and the occupants say it sounds whenever someone showers. What is the best recommendation?

    • A.Relocate it at least 3 ft from the bathroom door✓ Answer
    • B.Relocate it at least 10 ft from the bathroom door
    • C.Replace it with a heat alarm in the same spot
    • D.Leave it; nuisance alarms are an occupant issue

    IRC R314.3 requires smoke alarms to be at least 3 ft horizontally from the door or opening of a bathroom that contains a tub or shower, unless that would prevent a required placement, because shower steam sets alarms off. Repeated false alarms lead occupants to disable them, so relocating the alarm is a real safety fix. The 10 ft and 20 ft figures belong to the cooking-appliance rule, and a heat alarm is not a substitute for a required smoke alarm.

    Ref QB-G2EYGWSource: 2021 IRC R314.3 Location (not less than 3 ft horizontally from a bathroom door with a tub or shower)Report a problem with this question

  14. 14. Steel security bars cover the only window in a basement bedroom. The window's net clear opening meets the size rules, but the bars are screwed to the frame and have no release on the inside. What should the inspector report?

    • A.Acceptable: the opening still meets the size rules
    • B.Acceptable: a key for the bars is kept by the window
    • C.Defect: security bars are banned on escape windows
    • D.Defect: the bars must release from inside without tools✓ Answer

    IRC R310.4.4 allows bars, grilles and screens over an emergency escape and rescue opening only if they are releasable or removable from the inside without a key, a tool or more force than the window itself needs. In a fire, a sleeper cannot find a key or a screwdriver in the dark, so screwed-on bars defeat an opening that is otherwise large enough. Bars are not banned outright; they need a compliant release, and the NHIE outline lists window security bar release as an egress item.

    Ref QB-ZHK54XSource: 2021 IRC R310.4.4 Bars, grilles, covers and screens; NHIE 2023 content outline Domain 1 Task 13.1 (window security bar release)Report a problem with this question

  15. 15. A finished bedroom is built over an attached garage. The garage ceiling is covered with 1/2 in regular gypsum board in good condition. What should the inspector report?

    • A.Acceptable: 1/2 in gypsum on the garage side is enough
    • B.Deficient: the ceiling needs 5/8 in Type X gypsum✓ Answer
    • C.Deficient: the ceiling needs a 2-hour rated assembly
    • D.Acceptable: only the common wall needs fire separation

    IRC Table R302.6 requires at least 1/2 in gypsum board on the garage side between the garage and the residence, but at least 5/8 in Type X gypsum board where habitable rooms are above the garage. Type X board has glass fibers that hold it together longer in a fire, protecting the people sleeping overhead. A 2-hour assembly is not required for a one-family garage, so the inspector reports the ceiling as deficient and refers it to a qualified contractor.

    Ref QB-H2SAPXSource: 2021 IRC Table R302.6 Dwelling-garage separation (5/8 in Type X from habitable rooms above the garage)Report a problem with this question

  16. 16. In a side-by-side two-family dwelling with no sprinkler system, the inspector enters the attic and finds the framing open from one unit to the other, with no wall or draft stop above the shared wall. What should be reported?

    • A.Defect: the 1-hour separation does not reach the roof✓ Answer
    • B.Acceptable: separation applies only at a lot line
    • C.Acceptable: the ceiling drywall acts as the separation
    • D.Defect: each unit needs its own 2-hour wall to the roof

    IRC R302.3 requires units in a two-family dwelling to be separated by 1-hour fire-resistance-rated walls and floors whether or not a lot line exists, and the wall must run from the foundation to the underside of the roof sheathing. An open attic lets fire spread across the top of the building into the neighboring unit. The only attic exception needs 5/8 in Type X ceilings plus a draft stop and protected framing, none of which is present here, so the inspector reports the gap and refers it to a qualified contractor.

    Ref QB-2JXF9YSource: 2021 IRC R302.3 Two-family dwellings (1-hour separation, foundation to underside of roof sheathing, regardless of lot line)Report a problem with this question

  17. 17. Running an attached garage's door opener with the wall button, the inspector breaks the photo-eye beam while the door is closing. The door keeps going down until it reaches the floor. Under the InterNACHI Standards of Practice, what should be reported?

    • A.Nothing: auto-reverse checks fall outside the standards
    • B.Nothing: contact reversal is the only required safety
    • C.Defect: the photo-eye sensors failed to stop the door✓ Answer
    • D.Limitation: only a technician may test the sensors

    InterNACHI SOP 3.10 tells the inspector to operate garage door openers with normal controls and to report photo-electric safety sensors that did not operate properly. Its exclusion covers only verifying the pressure-activated auto-reverse feature, not the photo eyes. The federal opener standard, 16 CFR 1211, requires inherent reversal within 2 seconds of contact, but the photo eye is a separate layer that stops the door before it touches a child, so the failure is reported and referred to a garage door technician.

    Ref QB-J25NUYSource: InterNACHI Home Inspection Standards of Practice 3.10 Doors, Windows and Interior (III: photo-electric safety sensors that did not operate properly; IV exclusions); 16 CFR 1211.7(b) inherent entrapment protectionReport a problem with this question

  18. 18. The home's heating and cooling are controlled only by a smart thermostat linked to the seller's phone app. The wall unit shows a PIN lock screen, and no code or app access is provided. What is the best approach?

    • A.Report the heating and cooling as inoperative
    • B.Jumper the thermostat wires at the furnace to test
    • C.Factory-reset the thermostat to clear the PIN
    • D.Report it as a limitation and advise a later test✓ Answer

    InterNACHI SOP 2.2 says the inspector is not required to operate any system that needs special keys, codes, combinations or devices, and a home inspection uses only normal operating controls. Jumpering wires or resetting the device is invasive and can erase the owner's settings. Calling the system inoperative would be an unsupported finding, so the inspector states what was not tested and why, and the NHIE outline lists smart-technology limitations as a reporting task.

    Ref QB-THF53QSource: InterNACHI Home Inspection Standards of Practice 2.2 Exclusions (not required to operate systems requiring special keys, codes, combinations or devices); NHIE 2023 content outline Domain 2 Task 2.3Report a problem with this question

  19. 19. Radon testing is outside the inspector's standard of practice, but the buyer shares a long-term radon test from the home's lowest lived-in level showing 6 pCi/L and asks what EPA guidance says. What is the best response?

    • A.No action needed: EPA's action level is 10 pCi/L
    • B.Recommend mitigation by a qualified radon professional✓ Answer
    • C.No action needed: 6 pCi/L is the U.S. indoor average
    • D.Ventilate the basement for a week, then call it fixed

    EPA recommends fixing a home when radon is 4 pCi/L or more, and says to consider fixing between 2 and 4 pCi/L because there is no known safe level. The U.S. indoor average is about 1.3 pCi/L, so 6 pCi/L is well above it. Radon is a lung-cancer risk, and opening windows only dilutes it for a while, so the right referral is a qualified radon mitigation professional rather than an inspector's own fix.

    Ref QB-B2NANQSource: U.S. EPA, What is EPA's Action Level for Radon and What Does it Mean? (fix at 4 pCi/L or more; consider 2 to 4 pCi/L; average 1.3 pCi/L); InterNACHI SOP 2.2 Exclusions (radon)Report a problem with this question

  20. 20. While operating a freestanding range, the inspector presses lightly down on the open oven door and the back of the range lifts off the floor. What should be reported?

    • A.Safety defect: the anti-tip bracket is missing or loose✓ Answer
    • B.Acceptable: a range is held in place by its own weight
    • C.Minor item: adjust the leveling legs to stop the rocking
    • D.Acceptable: anti-tip devices are needed on gas ranges only

    The NHIE content outline lists a missing anti-tip bracket as a common safety issue for installed kitchen appliances. A freestanding range is light at the back, so weight on the open door, such as a child standing on it, can tip the whole range forward and spill hot pots onto the person. The bracket anchors the rear foot whether the range is gas or electric, and leveling legs do not prevent tipping, so the inspector reports it as a safety defect for correction.

    Ref QB-SSWYJZSource: NHIE 2023 content outline (PSI bulletin 3834), Domain 1 Task 11 D.4 Installed kitchen appliances: common safety issues (missing anti-tip bracket)Report a problem with this question

  21. 21. On a dry, sunny day you find a brown water stain on a top-floor bedroom ceiling below the attic. The drywall around it looks sound. What is the BEST action?

    • A.Call it old cosmetic staining since it appears dry today
    • B.Name the roof as the leak source and price the repair
    • C.Meter the stain, look in the attic above, report, refer out✓ Answer
    • D.Cut a test hole in the drywall to find the leak source

    The NHIE outline lists moisture stains as interior defects caused by defects in OTHER systems, and it names moisture meters as the test instrument for this kind of qualitative check. So you test the stain and look at the roof framing above it, then report the stain and refer it to a qualified contractor to find the source. A stain that is dry on a sunny day may still leak when it rains, so you cannot call it old. A home inspection is non-invasive, which rules out cutting drywall. Pinning the leak on the roof and pricing the repair goes past describing the defect into diagnosing it.

    Ref QB-9ARTYYSource: NHIE content outline (EBPHI 2023, PSI bulletin 3834) Domain 1 Task 11A.iii (moisture stains caused by other systems); Domain 2 Task 2.iii (moisture meters); InterNACHI SOP 1.1 (non-invasive visual examination)Report a problem with this question

  22. 22. A fixed glass sidelight is next to a hinged entry door, in the same plane as the closed door. The nearest edge of the glass is 10 in from the door, the bottom of the glass is 40 in above the floor, and the pane is about 6 sq ft. You see no safety-glazing label. What is the BEST report?

    • A.Hazardous location: safety glazing needed, none is labeled✓ Answer
    • B.Not hazardous: glass over 36 in above the floor is exempt
    • C.Not hazardous: only glass inside the door itself counts
    • D.Hazardous only if the pane is larger than 9 sq ft in area

    Under IRC R308.4.2, glazing next to a door is a hazardous location when its bottom edge is less than 60 in above the floor and it lies within 24 in of either side of the door, in the plane of the closed door. This sidelight is 10 in away with its bottom at 40 in, so it needs safety glazing, and the missing label should be reported. The 9 sq ft area and 36 in top-edge tests belong to the separate rule for ordinary windows (R308.4.3), not glass next to doors.

    Ref QB-TS9BR2Source: 2021 IRC R308.4.2 Glazing adjacent to doors (bottom edge under 60 in; within 24 in of door in plane of closed door); R308.4.3 Glazing in windowsReport a problem with this question

  23. 23. Measuring an interior basement stair, the inspector finds every tread is a uniform 9 in deep (nosing to nosing), every riser is 7-1/2 in, and the treads have a 1 in nosing. What should be reported?

    • A.Defect: risers are too tall; the maximum height is 7 in
    • B.Acceptable: uniform treads only need to vary under 3/8 in
    • C.Acceptable: the minimum tread depth is 9 in with a nosing
    • D.Defect: treads are too shallow; the minimum depth is 10 in✓ Answer

    IRC R311.7.5.2 requires a tread depth of at least 10 in, measured horizontally between the foremost projections (nosings) of adjacent treads. A 9 in tread is too short and makes footing less secure. The 7-1/2 in risers are under the 7-3/4 in maximum, so they are fine. The 3/8 in rule limits variation within a flight and does not replace the minimum depth. The nosing projection is a separate requirement and does not lower the 10 in minimum.

    Ref QB-AA4662Source: 2021 IRC R311.7.5.2 Treads (not less than 10 in); R311.7.5.1 Risers (7-3/4 in max)Report a problem with this question

  24. 24. At an interior basement stairway, a beam crosses over the stair. Measured vertically from the sloped line of the tread nosings, the bottom of the beam is 6 ft 4 in above the stair. How should this be reported?

    • A.Acceptable: stair headroom must be at least 6 ft 0 in
    • B.Defect: stair headroom must be at least 6 ft 8 in✓ Answer
    • C.Acceptable: headroom rules apply only to main stairs
    • D.Defect: stair headroom must be at least 7 ft 0 in

    IRC R311.7.2 requires stairway headroom of at least 6 ft 8 in, measured vertically from the sloped line along the tread nosings. That is the measurement used here, so 6 ft 4 in is 4 in short and is a head-strike hazard to report. The rule covers all stairways in the dwelling, basement stairs included. 7 ft is a common confusion with ceiling-height and commercial figures.

    Ref QB-USMNW3Source: 2021 IRC R311.7.2 Headroom (not less than 6 ft 8 in)Report a problem with this question

  25. 25. A basement bedroom's egress window opens into an area well that is 52 in deep, projects 40 in from the wall and is 48 in wide. The window opens fully, but the well has no ladder or steps. What should be reported?

    • A.Defect: the well must project at least 48 in from the wall
    • B.Acceptable: ladders are needed only in wells over 60 in deep
    • C.Defect: a well deeper than 44 in needs a fixed ladder or steps✓ Answer
    • D.Acceptable: the well needs only 9 sq ft of area to comply

    IRC R310.4.2 requires an approved, permanently fixed ladder or steps in any area well deeper than 44 in, so an occupant can climb out and a rescuer can climb in. At 52 in deep with no ladder, this well is a life-safety defect. The size is fine: R310.4.1 needs 9 sq ft of area with at least 36 in of projection and width, and 40 x 48 in is about 13.3 sq ft. Meeting the area rule does not excuse the missing ladder.

    Ref QB-BAFGB3Source: 2021 IRC R310.4.2 Ladder and steps (area wells deeper than 44 in); R310.4.1 Minimum size (9 sq ft, 36 in projection and width)Report a problem with this question

  26. 26. Behind the clothes dryer, a white flexible plastic duct runs into the wall cavity and through the wall to the exterior hood. What is the BEST report?

    • A.Acceptable if the plastic duct is listed and under 8 ft long
    • B.Defect: the concealed duct must be smooth-wall metal duct✓ Answer
    • C.Acceptable because it ends outdoors and not in the attic
    • D.Defect only if lint is visible at the exterior hood flap

    IRC M1502.4.1 requires dryer exhaust ducts to be metal, at least No. 28 gage, with a smooth interior and a 4 in nominal diameter. Plastic flex ribs trap lint and the material burns, so it is reported as a fire-safety defect wherever it runs. The 8 ft limit applies only to a listed transition duct (UL 2158A) between the dryer and the wall, and that duct may not be concealed. Ending outdoors meets only the termination rule, not the material rule.

    Ref QB-VSYY35Source: 2021 IRC M1502.4.1 Material and size (metal, No. 28 gage, smooth interior, 4 in); M1502.4.3 Transition ductReport a problem with this question

  27. 27. The dryer exhaust ends at an exterior wall hood that has a working backdraft flap, plus a fine wire screen added over the outlet to keep birds out. What should be reported?

    • A.Acceptable; a screen is required to keep out birds and pests
    • B.Remove the flap; backdraft dampers restrict dryer airflow
    • C.Acceptable; screens are banned only on bath fan outlets
    • D.Remove the screen; screens are not allowed at dryer outlets✓ Answer

    IRC M1502.3 requires a dryer exhaust termination to have a backdraft damper and says screens shall not be installed there. A screen catches lint, clogs the outlet and creates a fire hazard. So the flap is correct and the screen is the defect. Screens are only required on other exhaust and intake openings (R303.6).

    Ref QB-CATTG4Source: 2021 IRC M1502.3 Duct termination (backdraft damper required; screens shall not be installed)Report a problem with this question

  28. 28. In the attic, the inspector finds that the bathroom exhaust fan's flexible duct ends loose a few feet from the fan, near a soffit vent. What should be reported?

    • A.Defect: extend the duct so it discharges to the outdoors✓ Answer
    • B.Acceptable: the soffit vents carry the moist air outside
    • C.Acceptable: bath fans may discharge into a vented attic
    • D.Defect: the duct should be connected to the ridge vent

    IRC M1501.1 requires air removed by every mechanical exhaust system to discharge outdoors, and it names an attic, soffit, ridge vent or crawl space as places air must not be exhausted into. Moist bath air dumped into the attic can condense on the sheathing and lead to mold and decay. Passive attic vents do not count as an outdoor termination, and neither does connecting the duct to the ridge vent.

    Ref QB-WSBB96Source: 2021 IRC M1501.1 Outdoor discharge (not into an attic, soffit, ridge vent or crawl space)Report a problem with this question

  29. 29. A masonry wood-burning fireplace opening measures 36 in wide by 30 in high (7.5 sq ft). The noncombustible hearth extension projects 16 in in front of the opening and 8 in beyond each side. What should be reported?

    • A.Acceptable: 16 in in front and 8 in each side are required
    • B.Too small: 20 in in front and 12 in each side are required✓ Answer
    • C.Too small: 24 in in front and 12 in each side are required
    • D.Too small: 20 in in front and 8 in each side are required

    IRC R1001.10 requires a hearth extension of at least 16 in in front and 8 in on each side, but when the fireplace opening is 6 sq ft or larger it must be at least 20 in in front and 12 in on each side. This 7.5 sq ft opening triggers the larger size, so the 16 x 8 in extension is too small and leaves embers able to land on combustible flooring.

    Ref QB-DA66P5Source: 2021 IRC R1001.10 Hearth extension dimensions (16 in/8 in; 20 in/12 in where opening is 6 sq ft or larger)Report a problem with this question

  30. 30. A masonry chimney rises 3 ft above the point where it passes through the roof. A taller section of the same roof, 6 ft away horizontally, rises 1 ft higher than the top of the chimney. What should be reported?

    • A.Acceptable: it is 3 ft above the roof penetration point
    • B.Too short: it must be 3 ft above anything within 20 ft
    • C.Too short: it must be 2 ft above anything within 10 ft✓ Answer
    • D.Acceptable: the 10 ft rule applies only to the ridge

    IRC R1003.9 sets two tests that both apply. The chimney must be at least 3 ft above the highest point where it passes through the roof, and at least 2 ft higher than any portion of the building within 10 ft. This chimney passes the first test but fails the second, because roof within 6 ft rises above it, which can cause poor draft and downdrafts. Any part of the building within 10 ft counts, not only the ridge.

    Ref QB-5PVSS3Source: 2021 IRC R1003.9 Termination (2 ft higher than any portion of a building within 10 ft; not less than 3 ft above roof penetration)Report a problem with this question

  31. 31. Looking into a masonry wood-burning fireplace with a flashlight, the inspector sees a thick, black, tar-like deposit on the smoke chamber walls above the damper. The buyer asks whether the chimney is safe to use. Under a standard of practice such as InterNACHI's, what is the BEST response?

    • A.Report the deposit and refer to a chimney professional✓ Answer
    • B.Light a small test fire and judge the draft and smoke
    • C.Clear the flue for use because the damper operates
    • D.Scrape off the deposit to grade its creosote stage

    The NHIE outline names creosote buildup as a common fireplace safety issue, because the deposit can ignite and start a chimney fire. The InterNACHI SOP limits the inspector to visible, readily accessible parts. It says the inspector is not required to inspect the flue or vent system, determine the need for a chimney sweep, ignite fires, judge draft, or dismantle components. So you describe what you saw and refer the fireplace to a qualified chimney professional for evaluation before use. A working damper says nothing about whether the flue is safe.

    Ref QB-N63YC4Source: InterNACHI Home Inspection Standards of Practice 3.8 Fireplace IV (not required to inspect flue, determine need for chimney sweep, ignite fires, determine draft); NHIE content outline Task 12A (creosote buildup)Report a problem with this question

Other topics in this exam

Practice questions based on the National Home Inspector Examination content outline, widely shared home inspection standards of practice, and residential building science. Not affiliated with or endorsed by any examination board, licensing authority, or inspector association. A home inspection is a visual, non-invasive examination and is not a code-compliance inspection — nothing here should be read as a code requirement. Home inspection is regulated differently from place to place; confirm your own jurisdiction's requirements and the standards of practice you are held to before testing or inspecting. About the National Home Inspector Examination →