20 A2 — Automatic Transmission/Transaxle Practice Questions & Answers
Every A2 — Automatic Transmission/Transaxle practice question from the ASE Automotive Technician Practice Test, with the correct answer and a short explanation.
Start practice test →1. A vehicle with an automatic transaxle and a healthy engine is sluggish from a standing start, but once it reaches cruising speed it accelerates normally. Which of these could be the cause?
- A.A worn front fluid pump
- B.A slipping converter stator✓ Answer
- C.A low transmission fluid level
- D.A worn planetary pinion gear
The stator one-way clutch must lock at launch so the converter can multiply torque; if it freewheels, there is no multiplication and the car launches weakly. At cruising speed the stator freewheels by design, so acceleration is normal. A worn pump or low fluid causes slipping at all speeds, not only from a stop.
Ref QB-QX3FXESource: ASE 2026 Automobile Study Guide, A2 Task List A.12 (diagnose torque converter stator/one-way clutch failure) and A2 Sample Question 2Report a problem with this question
2. A transmission slips after a cold start but shifts firmly once it is fully warmed up. Which of these could be the cause?
- A.Line pressure below specification✓ Answer
- B.Line pressure above specification
- C.Restricted fluid cooler return line
- D.Worn output shaft rear bushing
Clutches and bands hold only when line pressure is high enough to clamp them; low line pressure lets them slip. Pressure above spec gives harsh, not slipping, engagements, and a restricted cooler line causes overheating rather than cold slip.
Ref QB-9FMXPGSource: ASE 2026 Automobile Study Guide, A2 Task List A.11 (perform hydraulic pressure tests) and A2 Sample Question 3Report a problem with this question
3. An electronically controlled automatic transaxle upshifts harshly during light, normal acceleration. A failure of which input could cause this?
- A.Upstream oxygen sensor
- B.Fuel tank pressure sensor
- C.Throttle position sensor✓ Answer
- D.Fuel level sending unit
The TCM uses throttle position as its engine-load input to set shift pressure and shift timing. If the sensor reports more throttle than the driver is using, the TCM raises apply pressure and the upshifts become harsh. The other sensors serve fuel and emissions control, not shift pressure.
Ref QB-RXES4GSource: ASE 2026 Automobile Study Guide, A2 Task List A.23 (diagnose shift quality problems from the electronic control system) and A2 Sample Question 4Report a problem with this question
4. The driver display shows a transmission over-temperature warning. On a road test, shift timing and quality are normal, but fluid temperature keeps climbing. Technician A says a restricted transmission fluid cooler could be the cause. Technician B says low line pressure could be the cause. Who is right?
- A.Technician A only✓ Answer
- B.Technician B only
- C.Both technicians
- D.Neither technician
Technician A is right: a restricted cooler cannot reject heat, so the fluid overheats even though the hydraulic controls work and the shifts stay normal. Technician B is wrong: low line pressure would show up as slipping or soft, delayed shifts, which the road test did not find.
Ref QB-AFY9VHSource: ASE 2026 Automobile Study Guide, A2 Task List A.10 (diagnose fluid loss and condition problems) and B.5 (inspect transmission cooler), A2 Sample Question 5Report a problem with this question
5. In a CVT, the TCM controls the ratio with separate primary-up and primary-down solenoids. On a road test the CVT moves normally toward higher (overdrive) ratios but will not move back toward lower ratios. Which of these could be the cause?
- A.An open in the primary-up solenoid circuit
- B.An open in the lock-up solenoid circuit
- C.An open in the primary-down solenoid circuit✓ Answer
- D.A shorted fluid temperature sensor circuit
Each ratio direction has its own solenoid, so a fault that stops only one direction points to that direction's circuit. An open in the primary-down circuit means the TCM's command never reaches the solenoid, so the ratio cannot move down. The up-ratio solenoid clearly works, and the lock-up and temperature circuits do not drive the ratio change.
Ref QB-SXS4AHSource: ASE 2026 Automobile Study Guide, A2 Task List A.19 (diagnose electronic controls using diagrams and schematics) and A2 Sample Question 6 (CVT solenoid schematic)Report a problem with this question
6. Transmission DTCs were stored on an OBD II vehicle, and the fault has now been repaired. Technician A says disconnecting the battery is an acceptable way to clear the codes. Technician B says to clear the codes with a scan tool, then run the OBD II monitors to verify the repair. Who is right?
- A.Technician A only
- B.Technician B only✓ Answer
- C.Both technicians
- D.Neither technician
Only Technician B is right. ASE's answer for clearing codes after a repair is a scan tool, followed by running the monitors so the system itself confirms the fault is gone. Disconnecting power can also erase adaptive values and other stored data, and it does not verify the repair.
Ref QB-BFBM2KSource: ASE 2026 Automobile Study Guide, A2 Task List A.7 (clear DTCs, run all OBD II monitors, and verify the repair) and A2 Sample Question 7Report a problem with this question
7. After a transmission repair, the technician clears DTCs with a scan tool, but a permanent DTC for the same fault is still displayed. Which statement about the permanent DTC is correct?
- A.It erases after a battery disconnect
- B.It erases after a second scan tool clear
- C.It erases after 40 engine warm-up cycles
- D.It erases when its monitor runs and passes✓ Answer
Permanent fault codes are stored in non-volatile memory, and no scan tool command or power disconnect can erase them. After the other fault data is cleared, the OBD system erases the permanent code only when the monitor for that fault runs and finds the malfunction gone. The 40 warm-up cycle rule applies to self-erasing ordinary confirmed codes.
Ref QB-TX5FFJSource: California Code of Regulations, Title 13, Section 1968.2 (OBD II), (d)(2.5) Erasing a permanent fault code and (g)(4.4.6)(C); ASE 2026 A2 Task List A.6Report a problem with this question
8. Under the OBD II rules (outside the special misfire, evaporative, and fuel system cases), once the MIL is on for a malfunction, the system may turn it off after how many driving cycles in which the monitor runs and the fault is not present?
- A.2 sequential driving cycles
- B.3 sequential driving cycles✓ Answer
- C.40 sequential warm-up cycles
- D.10 sequential driving cycles
The regulation allows the MIL to go out after three subsequent sequential driving cycles in which the responsible monitor runs and the malfunction is no longer present. The 40 warm-up cycle figure is a different rule: it governs when the stored confirmed code may self-erase after the MIL is already off.
Ref QB-CFPX7MSource: California Code of Regulations, Title 13, Section 1968.2 (OBD II), (d)(2.3) Extinguishing the MIL and (d)(2.4) Erasing a confirmed fault code; ASE 2026 A2 Task List A.6Report a problem with this question
9. A rear-wheel-drive automatic will not move in REVERSE but upshifts normally through every forward gear. Its apply chart shows: REVERSE uses the direct clutch and the reverse band; 1st uses the forward clutch; 2nd uses the forward clutch and the intermediate band; 3rd and 4th use the forward clutch and the direct clutch. Which of these could be the cause?
- A.A failed direct clutch
- B.A slipping forward clutch
- C.A broken intermediate band
- D.A broken reverse band✓ Answer
Rule out any part that is proven good in another range. The direct clutch works in 3rd and 4th, which upshift normally, so it is not the cause. The forward clutch and intermediate band are not used in REVERSE. The only component unique to REVERSE is the reverse band, so a broken band explains the symptom.
Ref QB-UXGSMKSource: ASE 2026 Automobile Study Guide, A2 Task List A.14 (diagnose using service information and hydraulic diagrams) and A2 Sample Question 8 (clutch/band apply chart)Report a problem with this question
10. A shift solenoid gets battery voltage from a fused feed, and the TCM turns it on by grounding the control side. With the solenoid commanded ON, a DMM reads battery voltage to ground at BOTH solenoid terminals, and the solenoid does not operate. Which of these could be the cause?
- A.An open in the solenoid coil winding
- B.An open in the solenoid feed circuit
- C.An open in the solenoid control circuit✓ Answer
- D.A short to ground in the control circuit
Full voltage on both terminals means no current flows and nothing drops voltage across the coil, so the ground path from the TCM is not reaching the solenoid: there is an open between the solenoid and the TCM. An open coil would leave the control terminal near 0 V, an open feed would leave both terminals near 0 V, and a short to ground would pull the control side to 0 V and keep the solenoid on.
Ref QB-PJ5AG3Source: ASE 2026 Automobile Study Guide, A2 Task List A.26 and A.27 (measure and interpret voltage with a DMM); circuit-reading method of A6 Sample Question 4 (DMM readings locating an open circuit)Report a problem with this question
11. A technician measures the current draw of a shift solenoid with a DMM. Which reading equals 0.75 amp?
- A.7.5 milliamps
- B.75 milliamps
- C.750 milliamps✓ Answer
- D.7500 milliamps
One amp equals 1,000 milliamps, so 0.75 A multiplied by 1,000 is 750 mA. Misplacing the decimal by one place is a common DMM-reading error that leads to condemning a good solenoid or missing a bad one.
Ref QB-73BF34Source: ASE 2026 Automobile Study Guide, A2 Task List A.27 (measure and interpret amperage with a DMM); unit conversion as in A6 Sample Question 8Report a problem with this question
12. A vehicle intermittently sets several unrelated transmission and network DTCs and shifts erratically. Before condemning the TCM, what should the technician check first?
- A.Battery, charging output, power and grounds✓ Answer
- B.TCM software level against latest calibration
- C.Shift solenoid resistance at the valve body
- D.Hydraulic line pressure in every gear range
Several unrelated codes in more than one system point to something they all share: supply voltage and ground. Low system voltage or a poor ground makes modules and solenoids act erratically and set false DTCs, so the battery, charging system, and power and ground circuits are verified before replacing or reprogramming a module.
Ref QB-QJGMN4Source: ASE 2026 Automobile Study Guide, A2 Task List A.21 (verify charging system; check batteries, connections, and power/ground circuits) and A.20 (data communications)Report a problem with this question
13. With the selector in PARK on a slight grade, the vehicle rolls. Technician A says misadjusted shift linkage or cable could be the cause. Technician B says a one-way roller clutch installed backwards could be the cause. Who is right?
- A.Technician A only✓ Answer
- B.Technician B only
- C.Both technicians
- D.Neither technician
PARK is held mechanically by the parking pawl, which the manual shift linkage moves into the output gear; if the linkage is off, the pawl may not fully engage. A backwards one-way clutch affects drive or freewheeling in a gear range, not the parking pawl, so Technician B is wrong.
Ref QB-83PS85Source: ASE 2026 Automobile Study Guide, A2 Task List B.1 (inspect, adjust, and replace manual valve shift linkage and cables); ASE 2024 Automobile Study Guide, A2 Sample Question 1Report a problem with this question
14. The engine cranks and starts with the gear selector in DRIVE. Which of these is the most likely cause?
- A.A misadjusted brake-shift interlock
- B.A misadjusted transmission range sensor✓ Answer
- C.An open in the starter relay coil circuit
- D.A shorted fluid temperature sensor circuit
The transmission range sensor also works as the neutral safety (inhibitor) switch: it should allow cranking only in PARK or NEUTRAL. If it is misadjusted, it can report P or N while the valve is in DRIVE. An open starter relay circuit would prevent cranking, and the brake-shift interlock only controls moving the selector out of PARK.
Ref QB-RJUXT5Source: ASE 2026 Automobile Study Guide, A2 Task List B.1 (transmission range sensor/switch, inhibitor/neutral safety switch)Report a problem with this question
15. When reinstalling a valve body, how should its fasteners be tightened?
- A.Outer bolts first, then tighten by feel
- B.With an impact at its lowest setting
- C.To the maximum torque for the bolt size
- D.To specification in the set sequence✓ Answer
The valve body is a precision part with tight valve bore clearances and a gasket or spacer plate that must seal evenly. Tightening to the specified torque in the specified sequence clamps it evenly; uneven or excess torque can distort the casting, bind valves, and cause internal cross-leaks.
Ref QB-9325E6Source: ASE 2026 Automobile Study Guide, A2 Task List B.7 (torque valve body fasteners to specification using the proper sequence)Report a problem with this question
16. A fluid and filter change has been done on a transmission that has no dipstick. Technician A says the level can be checked at any fluid temperature, because there are no hot or cold marks to read. Technician B says the vehicle must be level during the fluid level check. Who is right?
- A.Technician A only
- B.Technician B only✓ Answer
- C.Both technicians
- D.Neither technician
Only Technician B is right. Fluid expands as it heats, so on units without a dipstick the level is checked at the temperature the procedure specifies, often read on a scan tool, which makes Technician A wrong. The vehicle must also be level, because any tilt moves fluid toward or away from the check plug and gives a false reading.
Ref QB-SJ7AZ6Source: ASE 2026 Automobile Study Guide, A2 Task List B.12 and A.4 (verify fluid level and type with or without a dipstick) and A2 Sample Question 1Report a problem with this question
17. After a replacement TCM is installed, the transmission shifts harshly and erratically. Which step was most likely skipped?
- A.Clearing DTCs by unplugging the battery
- B.Programming the TCM and running relearn✓ Answer
- C.Replacing the fluid filter and gasket
- D.Adjusting the shift cable at the lever
A new TCM must be programmed or coded for the specific vehicle, and the adaptive values it uses to time clutch fill and apply must be relearned. Without programming and relearn, the module runs default or wrong settings, which shows up as harsh, erratic shifts. A filter or cable job would not change electronic shift control.
Ref QB-A3DFK7Source: ASE 2026 Automobile Study Guide, A2 Task List A.25 (program, reprogram, code, initialize, and/or set up control modules) and C.6 (re-learn and adaptation procedures)Report a problem with this question
18. Excessive input shaft end play could be caused by any of these EXCEPT:
- A.a worn selective-fit thrust washer
- B.worn friction plates in a clutch pack✓ Answer
- C.worn thrust surfaces in the case
- D.a worn planetary carrier thrust face
Shaft end play is the stack-up of thrust surfaces along the shaft's axis: selective washers, thrust washers and bearings, case thrust surfaces, and carrier thrust faces. Wear on any of these adds end play. Worn friction plates increase clearance inside that clutch pack, but they are not part of the shaft's thrust stack-up.
Ref QB-TJJM68Source: ASE 2026 Automobile Study Guide, A2 Task List C.10 (check end play) and C.12 (thrust washers and bearings); ASE 2024 Automobile Study Guide, A2 Sample Question 8Report a problem with this question
19. With the pan and valve body removed, a technician suspects a leaking clutch piston seal is causing a slip in one range. What is the best way to pinpoint the leak?
- A.Perform a converter stall test
- B.Check line pressure in that range
- C.Air test the clutch apply passage✓ Answer
- D.Replace the filter and recheck
Applying regulated air to the clutch's feed passage should give a firm thump as the piston applies; a hissing leak or weak apply points directly to the faulty seal or passage. A stall test or line pressure check needs the valve body installed and only shows that a range slips, not where the leak is.
Ref QB-B3RSR8Source: ASE 2026 Automobile Study Guide, A2 Task List C.21 (air test the operation of clutch and servo assemblies); ASE 2024 Automobile Study Guide, A2 Sample Question 5Report a problem with this question
20. A replacement valve body and solenoid assembly comes with its own calibration identification code. After installing it, what should the technician do with the scan tool?
- A.Clear DTCs only; the TCM adapts by itself
- B.Copy the old valve body's ID into the TCM
- C.Reset the oil life monitor and road test
- D.Enter the new ID, then perform relearn✓ Answer
The calibration ID tells the TCM the measured flow and pressure characteristics of that specific solenoid and valve body assembly. Entering the new ID with the scan tool and then running the relearn or adaptation procedure lets the TCM control pressure correctly. Keeping the old ID or relying on self-adaptation leaves the module controlling hardware that is no longer installed.
Ref QB-W2WG2ZSource: ASE 2026 Automobile Study Guide, A2 Task List C.6 (update software calibration settings and solenoid/valve body calibration identification numbers; perform re-learn and adaptation)Report a problem with this question
Other topics in this exam
Practice questions written to the ASE Automobile & Light Truck (A-series) task lists and standard automotive service principles. ASE is a mark of the National Institute for Automotive Service Excellence; this site is not affiliated with or endorsed by ASE. Always follow the vehicle manufacturer's service information for specifications and procedures on a real repair. About the ASE tests →